Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: kraftaroni
Showing results 1 to 10 of 10
Search took 0.00 seconds.
Forum: Do It Yourself, Boating on a Budget
08-26-2009, 03:23 PM
Replies: 8
Views: 14,526
Posted By kraftaroni

Flat Tappet. I'm sure it has a special grind...

Flat Tappet. I'm sure it has a special grind because of the EFI. ??
Forum: Do It Yourself, Boating on a Budget
08-26-2009, 12:11 AM
Replies: 8
Views: 14,526
Posted By kraftaroni

Good luck with your sale. I already have all my...

Good luck with your sale. I already have all my parts for the rebuild minus a cam..!!! Have my motor out and torn down. Just need cam specs so I can order a cam close to the stock profile. Looks like...
Forum: Do It Yourself, Boating on a Budget
08-25-2009, 03:11 PM
Replies: 8
Views: 14,526
Posted By kraftaroni

The part number is 431-4734 i don't know the...

The part number is 431-4734 i don't know the specs I need them as well. Anyone?? I killed a piston and half my cam lobes. Hope some cam guru's chime in.
Forum: General Q & A
08-25-2009, 01:28 PM
Replies: 6
Views: 2,861
Posted By kraftaroni

Anyone else out there that might have the...

Anyone else out there that might have the specs??? Anyone Anyone.. Bueler bueler. :)
Forum: General Q & A
08-25-2009, 11:35 AM
Replies: 6
Views: 2,861
Posted By kraftaroni

I Looked it up it's a standard rotation.. Only...

I Looked it up it's a standard rotation.. Only correct craft has a R/H rotation prop because the reduction drive turns it around?? Anyone have the specs on the 454 Magnum MPI cam? I can get it cam...
Forum: General Q & A
08-25-2009, 10:29 AM
Replies: 6
Views: 2,861
Posted By kraftaroni

It gives me part number 431-4734 for the cam...

It gives me part number 431-4734 for the cam shaft? But no Specs. My boat is a direct drive with a center mounted engine is it a reverse rotation? I didn't think it was? Anyone? It's a Malibu 1994...
Forum: General Q & A
08-25-2009, 01:28 AM
Replies: 6
Views: 2,861
Posted By kraftaroni

Where should I get a cam?? What are my options?/...

Where should I get a cam?? What are my options?/ I dont want to recalibrate my ecu if at all possible. I have EMI manifolds and an aftermarket fuel pump/regulator with return system on the boat but...
Forum: General Q & A
08-25-2009, 01:25 AM
Replies: 6
Views: 2,861
Posted By kraftaroni

94' 454 magnum efi 20ft ski boat

Long story short. I cracked a piston and had to tear my engine down. Looks like I need a bore so I'm going .030 over. I think I'm going with .095 dome top pistons because that is the closest I can...
Forum: General Q & A
07-19-2005, 01:53 AM
Replies: 4
Views: 3,047
Posted By kraftaroni

Re: 1995 454 mpi ??? mpi troubles

Correct The four pin plug. If you disconnect the pug the computer runs in a safe mode for diognosis if I am not mistaken? I have checked spark at the time when the problem has occured and it still...
Forum: General Q & A
07-18-2005, 02:42 AM
Replies: 4
Views: 3,047
Posted By kraftaroni

1995 454 mpi ??? mpi troubles

I have a 1995 454 mpi Inboard with hot/after running starting problems. It's not sending any trouble codes out except for a map sensor which I changed. It's runs great but it doesn't start at all if...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.