Offshoreonly.com - Search Results

Search: Posts Made By: troc

Showing results 1 to 25 of 86
Search took 0.01 seconds.

Forum: General Q & A

03-27-2019, 06:21 PM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

Did that , same timing curve

Did that , same timing curve

Forum: General Q & A

03-26-2019, 08:24 AM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

That is great thank you ! I will be dynoing this...

That is great thank you ! I will be dynoing this week Looking at inputs at ECM that control timing I will report back thanks again to all

Forum: General Q & A

03-21-2019, 06:09 PM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

agreed , ran some good fuel on the dyno and did...

agreed , ran some good fuel on the dyno and did exactly that...even with sensor wire disconnected the knock module is still in the circuit, no?

Forum: General Q & A

03-21-2019, 06:05 PM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

I think im going to find the ECM input that...

I think im going to find the ECM input that controlls knock next. TWO ecms doing the very same thing...starting to run out of ideas lol

Forum: General Q & A

03-21-2019, 05:20 PM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

I did , scanner matched timing light on the...

I did , scanner matched timing light on the balancer . timing starts to increase ,then just peels off as rpms increase I swapped out the knock sensor, but im wondering if i should check voltage on...

Forum: General Q & A

03-21-2019, 05:04 PM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

about 28 deg at 2700 then the timing starts to...

about 28 deg at 2700 then the timing starts to peel off down to 19deg as RPMs increase

Forum: General Q & A

03-21-2019, 04:56 PM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

Yes sir I used my rinda scanner

Yes sir I used my rinda scanner

Forum: General Q & A

03-21-2019, 04:51 PM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

yes sir, My friend 14apache said you were the man...

yes sir, My friend 14apache said you were the man to talk to lol

Forum: General Q & A

03-21-2019, 04:50 PM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

yes sir with my rinda scanner

yes sir with my rinda scanner

Forum: General Q & A

03-21-2019, 04:50 PM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

yes ,fuel pressure was 42 psi , known good set of...

yes ,fuel pressure was 42 psi , known good set of injectors swapped into manifold , the timing wont advance enough to make any real hp, I am starting to wonder if my buddy mechanic advanced the...

Forum: General Q & A

03-19-2019, 07:43 PM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

thanks Dan, Yes using the Rinda and base timing...

thanks Dan, Yes using the Rinda and base timing mode. Just cant get enough timing from the ECM....and had a few sets of eyes verify lol

Forum: General Q & A

03-19-2019, 06:42 PM

Replies: 23

7.4 mpi timing issues

Views: 7,488

Posted By troc

7.4 mpi timing issues

Hi , this one is for you EFI gurus Im involved with a 7.4 MPI gen VI that was initially reported to be running fine. the other inboard was removed due to a mechanical failure and my buddy thought...

Forum: Swap Shop

07-27-2012, 06:25 AM

Replies: 48

Cleaning Out The Garage....take A Look Bbc Parts

Views: 6,637

Posted By troc

do you still have the water pump.? I am...

do you still have the water pump.? I am interested in purchasing it thanks Cort

Forum: Drives and Lower Units

07-12-2011, 06:41 AM

Replies: 2

3a drive oil capacity?

Views: 1,217