Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Daytona30mike
Showing results 1 to 21 of 21
Search took 0.00 seconds.
Forum: General Q & A
04-21-2005, 03:44 PM
Replies: 6
Views: 14,860
Posted By Daytona30mike

Re: Can't get some of the new lifters to pump up. Help!

You need the right tool for priming. If you have an old distributor,
grind off all the teeth and stick it in the manifold with drill attached and it will build pressure to the lifters. If you are...
Forum: General Q & A
04-21-2005, 08:19 AM
Replies: 16
Views: 9,805
Posted By Daytona30mike

Re: manufacturer of lifter in GM 572

Thanks for all the information. I just thought that it was
too much pressure for the lifter also. But I can't believe GM
would not correct the specs if they were wrong. And I also
think if they...
Forum: General Q & A
04-20-2005, 05:20 PM
Replies: 16
Views: 9,805
Posted By Daytona30mike

Re: manufacturer of lifter in GM 572

Here is a Canadian link with the same specs...

http://www.saturnoflondon.saturncanada.com/english/maintenance/parts/performance/parts_perf_engines.html#ZZ572_620

ZZ572/620 Technical Information...
Forum: General Q & A
04-20-2005, 05:02 PM
Replies: 16
Views: 9,805
Posted By Daytona30mike

Re: manufacturer of lifter in GM 572

Thanks for the answers... Here is where I got the info...

http://www.sallee-chevrolet.com/ChevyBigBlockV8s/572.html

They show it as:

2498792 Long-Block Components (Short-Block Components...
Forum: General Q & A
04-20-2005, 01:49 PM
Replies: 16
Views: 9,805
Posted By Daytona30mike

manufacturer of lifter in GM 572

Does anyone know who manufactures the lifters in GM's 572 cu in
620 horsepower engine. It has a seat pressure of 197 pounds
and it is a hydraulic roller. Seems like alot of seat pressure and I...
Forum: General Q & A
12-15-2004, 10:06 AM
Replies: 39
Views: 6,961
Posted By Daytona30mike

Re: poor dyno score on 540,s

Check exaust gas temps to find out where the carb jetting needs to be. It is an excellent
way to tune the motor without trial and ERROR.

Mike
Forum: General Q & A
09-30-2004, 09:24 AM
Replies: 11
Views: 2,469
Posted By Daytona30mike

Re: Bravo one questions

When filling from propshaft up, be sure to take cap off of the reservoir to
prevent pressure buildup.

Mike
Forum: General Q & A
09-23-2004, 09:22 AM
Replies: 1
Views: 719
Posted By Daytona30mike

Drive temps...anyone checking?

I am running Imcos with 1.25 ratio with 800 N/A engines and
am seeing temps in the 230's on a hard run. I have thermo couplers
in the drives and am wondering if others have any idea what the...
Forum: General Q & A
07-22-2004, 09:16 AM
Replies: 11
Views: 1,554
Posted By Daytona30mike

Re: Same drive/ Engine problem

BigChief: For sure sounds like electrical now that we know the tach jerks. Just
check wires behind dash and on your coil, ignition, and even ground wires. It has to be in there somewhere. Let us...
Forum: General Q & A
07-21-2004, 12:32 PM
Replies: 38
Views: 3,867
Posted By Daytona30mike

Re: Losing Oil Pressure?

Cut the filter to see if anything came apart in the engine. Also, are both
engines oil level the same after sitting and after running???

Mike
Forum: General Q & A
07-21-2004, 09:51 AM
Replies: 11
Views: 1,554
Posted By Daytona30mike

Re: Same drive/ Engine problem

Watch the tach closely and see if it drops or jerks quickly. ...that would indicate
a short in the wiring. Check your other gauges that are electical for the same.

Then check fuel floats...
Forum: General Q & A
07-21-2004, 09:31 AM
Replies: 38
Views: 3,867
Posted By Daytona30mike

Re: Losing Oil Pressure?

What is your oil pan capacity??? You also need oil temp gauge. What weight
oil are you running and do you run any type oil thermostat? What brand oil pump
did you put in?

Sorry for all the...
Forum: General Q & A
05-17-2004, 01:53 PM
Replies: 10
Views: 3,723
Posted By Daytona30mike

Re: GA Performance Shops ?

I agree with MikeHTM. Gary Grimes is an excellent engine builder and tell
him Mike Miller from Tennessee told you to call him. He is in Alpherata GA.
Spelling for the city might be wrong.

Mike
Forum: General Q & A
05-10-2004, 09:14 AM
Replies: 11
Views: 2,542
Posted By Daytona30mike

Wette Vette: I use to run those Mallory but...

Wette Vette: I use to run those Mallory
but had many failures. Now run Weldon and NEVER have had any problems with them. The Mallory use to eat upthe burshes and just quit. No warning... Hope this...
Forum: General Q & A
02-20-2004, 04:52 PM
Replies: 164
Views: 17,867
Posted By Daytona30mike

Darin: Received my props from you for my 30"...

Darin:

Received my props from you for my 30" Eliminator and they look great. They sure don't look like they use too and I can see the amount of work that went into them.

Very Impressed to say...
Forum: General Q & A
01-08-2004, 12:07 AM
Replies: 6
Views: 1,455
Posted By Daytona30mike

HOT BLOODED: I have an 30 Eliminator Daytona...

HOT BLOODED:

I have an 30 Eliminator Daytona with twin 800 horsepower all aluminum naturally aspirated motors with Imco standoff boxes and drives. My boat is lighter than most and had problems...
Forum: General Q & A
01-04-2004, 11:15 PM
Replies: 14
Views: 3,635
Posted By Daytona30mike

HOUSTONPROP: Thanks for the offer and I will get...

HOUSTONPROP: Thanks for the offer and I will get in touch with you in the next day or so. I have seen you give great advise to a lot of members and see that you are highly respected.

I was trying...
Forum: General Q & A
01-04-2004, 02:32 PM
Replies: 14
Views: 3,635
Posted By Daytona30mike

rbtnt: When you say your drives are even...

rbtnt:

When you say your drives are even with the bottom of the boat, I assume or pretty sure you mean the bottom before the step.

Do you have any idea how much of your prop is in the tunnel...
Forum: General Q & A
01-03-2004, 07:05 PM
Replies: 14
Views: 3,635
Posted By Daytona30mike

Eliminator219 You are probably right about...

Eliminator219

You are probably right about different handling of the two boats with the weight factor being as it is. I just moved one drive close to a half inch as it was too close to the tunnel...
Forum: General Q & A
01-02-2004, 07:36 PM
Replies: 14
Views: 3,635
Posted By Daytona30mike

rbtnt... Thanks for the suggestion but the one...

rbtnt... Thanks for the suggestion but the one thing I am worried about is too much transom lift with the 36s. I have Aluminum motors and the boat is pretty light in the back end, so I am trying...
Forum: General Q & A
01-02-2004, 04:02 PM
Replies: 14
Views: 3,635
Posted By Daytona30mike

Prop advise 30' Eliminator Tunnel

I have a 30' Eliminator Daytona with twin 572 Aluminum motors that produce 800
horsepower each. Last year I ran 34"
bravos with 1.36 gearing in an Imco
drive and extention box. I was up against...
Showing results 1 to 21 of 21


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.