Offshoreonly.com - Search Results

Search: Posts Made By: NEthing4Speed

Showing results 1 to 9 of 9
Search took 0.00 seconds.

Forum: General Boating Discussion

05-05-2008, 05:49 PM

Replies: 21

Dreaded Milkshake

Views: 4,664

Posted By NEthing4Speed

I have had the boat out twice already, running it...

I have had the boat out twice already, running it hard,and there are no signs of the milkshake. I think I have fixed the problem. The repair looks like Frankenblock but is holding up nicely.

I...

Forum: General Boating Discussion

05-03-2008, 07:22 AM

Replies: 21

Dreaded Milkshake

Views: 4,664

Posted By NEthing4Speed

Make that 6,500 - 7,500 for this one. If I was...

Make that 6,500 - 7,500 for this one. If I was starting with a raw block I would definitely scrap it and find a new one. This block has close to 30 hours worth of machine work. I have to at least...

Forum: General Boating Discussion

05-02-2008, 10:45 PM

Replies: 21

Dreaded Milkshake

Views: 4,664

Posted By NEthing4Speed

Why do you say that? Do you think the leak will...

Why do you say that? Do you think the leak will continue? Or do you think it will crack somewher else? Have you experienced the same problem before?

Forum: General Boating Discussion

05-02-2008, 07:10 PM

Replies: 21

Dreaded Milkshake

Views: 4,664

Posted By NEthing4Speed

Found the source of the milkshake.

I found the leak! There is a 2 1/2" long crack under the intake running parallel with the deck of the block and the lifter valley. This is common with older 350 blocks. I am sure I magnafluxed the...

Forum: General Boating Discussion

05-02-2008, 03:53 PM

Replies: 21

Dreaded Milkshake

Views: 4,664

Posted By NEthing4Speed

Yes sir, I am looking at ways of getting heat...

Yes sir, I am looking at ways of getting heat into the oil. It is probably due to the motor being raw water cooled. That is with oil pressure between 45-60 psi at idle/WOT respectively.

I am...

Forum: General Boating Discussion

05-01-2008, 09:06 PM

Replies: 21

Dreaded Milkshake

Views: 4,664

Posted By NEthing4Speed

It has been over a year since I assembled the...

It has been over a year since I assembled the engine with a buddy of mine who owns an automotive machine shop. I don't recall exactly what gasket I used. I believe I ended up using a 400 head gasket...

Forum: General Boating Discussion

05-01-2008, 06:15 PM

Replies: 21

Dreaded Milkshake

Views: 4,664

Posted By NEthing4Speed

I pressure checked the risers with a plumbers...

I pressure checked the risers with a plumbers test ball and compressed air. The risers seem to be fine. I think I will move on to the intake manifold next.

BTW, I will scuttle the boat if it is a...

Forum: General Boating Discussion

05-01-2008, 09:20 AM

Replies: 21

Dreaded Milkshake

Views: 4,664

Posted By NEthing4Speed

Mark, The only oil heat exchanger I have is...

Mark,

The only oil heat exchanger I have is for the power steering fluid.

JC & Driven ,

I will go ahead and pressure test the risers as the manifolds already checked out with the initial...

Forum: General Boating Discussion

04-30-2008, 09:04 PM

Replies: 21

Dreaded Milkshake

Views: 4,664

Posted By NEthing4Speed

Dreaded Milkshake

Hello everyone. This is my first post, but I have been visiting the site for quite a while and have found a lot of useful information within the forums.

I am having a problem with water in my oil....

Showing results 1 to 9 of 9