Offshoreonly.com - Search Results

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: goin70
Showing results 1 to 12 of 12
Search took 0.02 seconds.
12-08-2018, 04:00 AM
Replies: 129
Views: 48,041
Posted By goin70

How is the testing coming along?

Have any other lower units been built and installed? I would be very interested in hearing any recent updates. I plan to rebuild my transom this winter and possibly be in the market in the Spring.
...
03-25-2017, 05:56 AM
Replies: 129
Views: 48,041
Posted By goin70

The finished product is a masterpiece! Not only...

The finished product is a masterpiece! Not only does it look great, it sounds to be reliable. Did you have a chance to compare the speed with and without the nose cone? Could you post a few more...
04-26-2016, 05:55 PM
Replies: 129
Views: 48,041
Posted By goin70

Two steps forward! What modifications did...

Two steps forward!

What modifications did you make on the transmission?

Good luck this weekend with the testing.
04-12-2016, 02:40 PM
Replies: 129
Views: 48,041
Posted By goin70

Great news about the improvements in handling....

Great news about the improvements in handling. What rpm are you looking to turn? At about what RPM does the transmission slip? I will be interested to hear your next steps. Good luck and please keep...
03-27-2016, 10:52 PM
Replies: 129
Views: 48,041
Posted By goin70

Motor numbers look great! This should give you...

Motor numbers look great! This should give you little extra giddy up.
02-18-2016, 08:35 PM
Replies: 129
Views: 48,041
Posted By goin70

Sorry to hear you had engine issues, but it...

Sorry to hear you had engine issues, but it sounds like you will have a strong bottom end with the upgraded rods and crank. Great news the outdrive held together and had a solid mph gain.

What RPM...
01-09-2016, 09:16 AM
Replies: 129
Views: 48,041
Posted By goin70

I took a few measurement and my prop shaft Is...

I took a few measurement and my prop shaft Is approx 7.5 inch below the bottom. It sounds like the setup you have might be a good place to start.

Any progress on the project? Please keep me...
12-27-2015, 07:21 PM
Replies: 129
Views: 48,041
Posted By goin70

The 4.750 might be a workable combination. Do you...

The 4.750 might be a workable combination. Do you have the ability to fine tune the depth if needed? It sounds like the prop selection will not be a problem.
12-27-2015, 05:37 PM
Replies: 129
Views: 48,041
Posted By goin70

Please keep me posted on the testing and...

Please keep me posted on the testing and production plans. Is it possible to change the depth from the current 4.750 without substantial cost? My engine is almost exactly the same output as you are...
12-27-2015, 03:49 PM
Replies: 129
Views: 48,041
Posted By goin70

Thanks! I need a apply a great deal of trim to...

Thanks! I need a apply a great deal of trim to get the TRS's deep drive, to any respectable speed. I have another friend with a Donzi X18 TRS that got excited about your project and interested if...
12-27-2015, 12:48 PM
Replies: 129
Views: 48,041
Posted By goin70

After taking a look at the setup, I noticed a...

After taking a look at the setup, I noticed a different trim ram than I am running. What model ram is on this setup and are you running a special trim pump? I still have the slow prestolite trim...
12-27-2015, 02:18 AM
Replies: 129
Views: 48,041
Posted By goin70

Awesome project! It is exactly what I could use...

Awesome project! It is exactly what I could use on my Cigarette 20 TRS, left rotation. I understand you are testing and please keep the results flowing. What would it approximately cost to make this...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.