Offshoreonly.com - Search Results

Search: Posts Made By: mcprodesign

Showing results 1 to 10 of 10
Search took 0.00 seconds.

Forum: Drives and Lower Units

10-03-2014, 11:23 AM

Replies: 23

best way to line up a bravo w a new motor?

Views: 4,637

Posted By mcprodesign

530285 Not mine but this is the one I have

530285 Not mine but this is the one I have

Forum: Drives and Lower Units

10-01-2014, 11:35 PM

Replies: 23

best way to line up a bravo w a new motor?

Views: 4,637

Posted By mcprodesign

i have a quicksilver alignment tool, hard to...

i have a quicksilver alignment tool, hard to believe but it has .050 slop when measured on the end of it with a dial indicator . See pic. I tuned my motor over and took a reading of .100 on the 180•...

Forum: Drives and Lower Units

09-01-2014, 09:55 PM

Replies: 23

best way to line up a bravo w a new motor?

Views: 4,637

Posted By mcprodesign

that is great advice and I totally agree. More...

that is great advice and I totally agree. More people should check the alignment when they have their drives off. The only reason that I thought to check it was because I put a brand new block in and...

Forum: Drives and Lower Units

08-17-2014, 10:31 PM

Replies: 23

best way to line up a bravo w a new motor?

Views: 4,637

Posted By mcprodesign

With everything bolted down the shaft was a bit...

With everything bolted down the shaft was a bit snug for the last little bit ( i could push it in with my thumb) so i hoisted on the front with it all bolted down. It felt a lot better. So i...

Forum: Drives and Lower Units

08-17-2014, 05:22 PM

Replies: 23

best way to line up a bravo w a new motor?

Views: 4,637

Posted By mcprodesign

You guys are so bomb. I kust brought this thread...

You guys are so bomb. I kust brought this thread back to say thanks. I had to loosen the bellhousing bolts to get the rear down as far as possible. Then loosen the front motor monts and hoist the...

Forum: Drives and Lower Units

07-20-2014, 11:56 AM

Replies: 23

best way to line up a bravo w a new motor?

Views: 4,637

Posted By mcprodesign

The angle is what you are aligning .The rear...

The angle is what you are aligning .The rear ,with proper hardware and mounts that haven't collapsed ,is a fixed height ...Once again the angle is what you are adjusting ...Do yourself a favor and...

Forum: Drives and Lower Units

07-20-2014, 11:55 AM

Replies: 23

best way to line up a bravo w a new motor?

Views: 4,637

Posted By mcprodesign

Thankyou. I puilled the motor and belhouse w the...

Thankyou. I puilled the motor and belhouse w the drive still on. Don't ask me how. I guess cause i am a rtetirted bodyman :) I will take the drive off before I put the motor in and see about what...

Forum: Drives and Lower Units

07-19-2014, 11:19 PM

Replies: 23

best way to line up a bravo w a new motor?

Views: 4,637

Posted By mcprodesign

Well I am not following this.If I adjust the...

Well I am not following this.If I adjust the front montoer mount I would be changing the angle of the crankshaft in comparisdon the the drive. Amnd I dont think i would want to change the angle?...

Forum: Drives and Lower Units

07-19-2014, 11:25 AM

Replies: 23

best way to line up a bravo w a new motor?

Views: 4,637

Posted By mcprodesign

Is thi sthe 2 bolts on the gimble right next to...

Is thi sthe 2 bolts on the gimble right next to the bellhousing on the motor? I have a Mercruiser alignment shaft

Forum: Drives and Lower Units

07-18-2014, 11:36 PM

Replies: 23

best way to line up a bravo w a new motor?

Views: 4,637

Posted By mcprodesign

best way to line up a bravo w a new motor?

I am guessing you put the dumby shaft in and adjust the highth on gimble with the 2 bolts until it spins the freeest. Is the correct?

Showing results 1 to 10 of 10