Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: GPM
Showing results 1 to 12 of 12
Search took 0.00 seconds.
Forum: General Q & A
Yesterday, 04:53 PM
Replies: 11
Views: 154
Posted By GPM

Maybe check with Cometic, they make intake...

Maybe check with Cometic, they make intake gaskets.
Forum: General Q & A
03-28-2021, 11:22 AM
Replies: 8
Views: 467
Posted By GPM

Lifters, Lash and Preload. What you don’t know...

Lifters, Lash and Preload. What you don’t know won’t hurt you, or will it? - Gwatney Performance (https://gwatneyperformance.com/lifters-lash-preload-dont-know-wont-hurt-will/)
Forum: General Q & A
01-03-2021, 03:06 PM
Replies: 25
Views: 1,421
Posted By GPM

Maybe add an intercooler for safety, are you...

Maybe add an intercooler for safety, are you planning to run a thermostat in the engine ?
Forum: General Q & A
12-19-2020, 03:43 PM
Replies: 10
Views: 808
Posted By GPM

Why wouldn't you try what you have and then make...

Why wouldn't you try what you have and then make the change if necessary,
Forum: General Q & A
12-16-2020, 06:11 PM
Replies: 53
Views: 2,445
Posted By GPM

The 110 lsa may be better for the street

The 110 lsa may be better for the street
10-05-2020, 07:29 PM
Replies: 34
Views: 2,851
Posted By GPM

I'm glad it worked out for you, Mr Gadets did the...

I'm glad it worked out for you, Mr Gadets did the rebuild
10-04-2020, 09:12 PM
Replies: 34
Views: 2,851
Posted By GPM

I over powered the hell out of them, used to get...

I over powered the hell out of them, used to get 3 passes out of a set of gears.
Forum: General Q & A
09-17-2020, 04:01 PM
Replies: 7
Views: 322
Posted By GPM

At some point, your drive will be your limiting...

At some point, your drive will be your limiting factor
Forum: General Q & A
07-21-2020, 05:20 PM
Replies: 28
Views: 1,572
Posted By GPM

It disapates heat but the plug needs to get hot...

It disapates heat but the plug needs to get hot enough to keep itself clean. I think it was the NGK site that I saw a nice explantion of proper heat range selection.
Forum: General Q & A
07-09-2020, 01:25 PM
Replies: 19
Views: 1,693
Posted By GPM

7500 always sounds good :D

7500 always sounds good :D
Forum: General Q & A
06-22-2020, 05:38 PM
Replies: 33
Views: 2,272
Posted By GPM

Tried one of those in a 383 sbc, Dart 200 cc...

Tried one of those in a 383 sbc, Dart 200 cc heads, it was done at 5100 rpm, and it was in a 20 ft Glastron
Forum: General Q & A
03-07-2005, 09:10 PM
Replies: 24
Views: 22,304
Posted By GPM

Re: 6.135 or 6.385 rod length?

Sure if you want a horrible rod to stroke ratio.
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.