Offshoreonly.com - Search Results

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: MILD THUNDER
Showing results 1 to 25 of 500
Search took 0.13 seconds.
Forum: General Q & A
08-29-2021, 08:11 PM
Replies: 266
Views: 35,584
Posted By MILD THUNDER

Kaama, I sold my boat two summers ago. So i been...

Kaama, I sold my boat two summers ago. So i been doing other things.

As far as that boat, it's idling in and out of gear and running pretty good all summer. After some tuning it was much better...
Forum: General Q & A
08-27-2021, 11:33 PM
Replies: 12
Views: 830
Posted By MILD THUNDER

I think the problem is, its a 632ci wet sump....

I think the problem is, its a 632ci wet sump. That thing needs to breath. For a wet sump 632ci, that sucker is going to need some good venting at high rpm/wot. All that crankcase psi needs somewhere...
Forum: General Q & A
08-27-2021, 03:59 PM
Replies: 266
Views: 35,584
Posted By MILD THUNDER

Kaama Mark, I have the tune Wesseldyke made for...

Kaama Mark, I have the tune Wesseldyke made for Alex Pratts outerlimits engines. Whats interesting, is in the reciepts, he charged a hefty amount for "tuning" or "building base tune" ....however the...
Forum: General Q & A
08-27-2021, 03:22 PM
Replies: 12
Views: 830
Posted By MILD THUNDER

Pcv does nothing at wot. Only while under vacuum....

Pcv does nothing at wot. Only while under vacuum. If it blew the crank seal, either blowby is excessive, or your breathers are too restrictive.
Forum: General Q & A
03-25-2021, 07:27 AM
Replies: 39
Views: 3,321
Posted By MILD THUNDER

Yet youre here seeking...

Yet youre here seeking advice.....:party-smiley-004:


Thats a bold statement, theres quite a few really sharp guys (and builders) on this thread offering help. Not the first "1400hp" procharged...
Forum: General Q & A
03-24-2021, 09:07 PM
Replies: 39
Views: 3,321
Posted By MILD THUNDER

Id be more worried about detonation. What octane...

Id be more worried about detonation. What octane fuel?

One issue I had , was the one holley iac harness i had, was wired for a chrysler iac. Well, plugging that into the LSX style IAC I had,...
Forum: General Q & A
02-19-2021, 02:52 PM
Replies: 6
Views: 641
Posted By MILD THUNDER

Id prob start with this 5.25" lower pulley. With...

Id prob start with this 5.25" lower pulley. With the 5.8 upper, that will be about 10% underdrive. Then, when he wants to run some race gas, flip the pulleys around, and probably have around 10-12psi...
10-30-2020, 11:07 PM
Replies: 80
Views: 21,774
Posted By MILD THUNDER

Ran like that for many years, no water stats....

Ran like that for many years, no water stats. Water Temp gauge never moved. Cold water temps are fine.
10-16-2020, 07:34 PM
Replies: 240
Views: 49,981
Posted By MILD THUNDER

Not sure how youre getting 9.5:1, using a 13cc...

Not sure how youre getting 9.5:1, using a 13cc dome piston, with quench of .037. Assuming the chambers measure out to 119-121cc, that makes it around 10:1.

i do believe with the cam you have, its...
Forum: General Q & A
10-15-2020, 09:52 PM
Replies: 63
Views: 11,013
Posted By MILD THUNDER

Im curious to see what the whipples IAT temps...

Im curious to see what the whipples IAT temps will be in comparison to his roots.

Thats a nice temp reduction with the meth!
Forum: General Q & A
10-15-2020, 09:38 PM
Replies: 63
Views: 11,013
Posted By MILD THUNDER

My post was in reference to icdedppls comments...

My post was in reference to icdedppls comments regarding his IAT temps being in the 110-120* range. Thats pretty decent. My NA engine doesnt get much cooler than that on a typical summer day. Im sure...
10-15-2020, 02:13 PM
Replies: 240
Views: 49,981
Posted By MILD THUNDER

Im not twitter or Facebook looking for censored...

Im not twitter or Facebook looking for censored opinions! Lol

All i know , is I pay $360-370 for a billet hyd or solid roller custom grind from comp. My cost. Never priced a sadi core , but id...
10-13-2020, 08:44 PM
Replies: 240
Views: 49,981
Posted By MILD THUNDER

$700 for one cam!?

$700 for one cam!?
10-13-2020, 01:08 PM
Replies: 240
Views: 49,981
Posted By MILD THUNDER

I mean with accessories and your wet exhaust on a...

I mean with accessories and your wet exhaust on a dyno. Not with dry dyno headers, and a pumped up correction factor
Forum: General Q & A
10-12-2020, 08:09 PM
Replies: 63
Views: 11,013
Posted By MILD THUNDER

not sure where all the heat talk comes from. My...

not sure where all the heat talk comes from. My NA 540ci in my car has IAT temps similar to your roots blower setup. Guys need to calm down with the heat talk. 🥴
10-12-2020, 07:39 PM
Replies: 240
Views: 49,981
Posted By MILD THUNDER

400-425 hp in full marine trim on a legitimate...

400-425 hp in full marine trim on a legitimate dyno. 550-600hp on salesmans dyno. Thats my guess.
Forum: Formula
09-03-2020, 08:20 AM
Replies: 25
Views: 8,448
Posted By MILD THUNDER

I sold it back in 2010 or so with no power. Just...

I sold it back in 2010 or so with no power. Just the hull , trailer and drives. It went to south carolina I believe, then to Tennessee/kentucky area, then to Michigan. Seems like its traded hands...
Forum: General Q & A
08-25-2020, 02:23 PM
Replies: 46
Views: 4,408
Posted By MILD THUNDER

The timing youre seeing with the gun, is the...

The timing youre seeing with the gun, is the actual timing thats taking place. 15* sounds low, but i dont have the table handy to compare what it should be, vs what it really is.

What version of...
Forum: General Q & A
08-25-2020, 02:07 PM
Replies: 46
Views: 4,408
Posted By MILD THUNDER

Not necessarily. The early mpi engines had a...

Not necessarily. The early mpi engines had a very lame timing curve. If you free rev them in nuetral , youll see the timing actually go way down, even negative timing. They did this to help prevent...
Forum: General Q & A
08-21-2020, 10:04 PM
Replies: 29
Views: 2,200
Posted By MILD THUNDER

These wiseco pistons are a good deal. Ive used...

These wiseco pistons are a good deal. Ive used them in a 540ci, and a 516ci. Usually you can find them around 500 for a set and they come with a file fit plasma moly ring set.
...
Forum: General Q & A
08-21-2020, 05:46 PM
Replies: 29
Views: 2,200
Posted By MILD THUNDER

Something else that can play a role is ignition...

Something else that can play a role is ignition timing. Modern oem vehicles retard the chit out of the timing on cold starts, because it heats up the catalytic converters in a hurry. Having too much...
Forum: General Q & A
08-20-2020, 02:08 PM
Replies: 29
Views: 2,200
Posted By MILD THUNDER

Dont forget most bbc flat top pistons have about...

Dont forget most bbc flat top pistons have about a 3 or 4cc valve relief
Forum: General Q & A
08-20-2020, 01:53 PM
Replies: 29
Views: 2,200
Posted By MILD THUNDER

Some edelbrocks have 110cc chamber, some 118cc...

Some edelbrocks have 110cc chamber, some 118cc depending on the model. Even with the 110cc, youll likely be sub 9:1 with a flat top
Forum: General Q & A
08-20-2020, 07:45 AM
Replies: 29
Views: 2,200
Posted By MILD THUNDER

No way are you anywhere near 9.5:1 with flat top...

No way are you anywhere near 9.5:1 with flat top pistons in a 468 with those heads
Forum: General Q & A
06-27-2020, 08:08 AM
Replies: 60
Views: 8,506
Posted By MILD THUNDER

The problem with the gasket is the block. If you...

The problem with the gasket is the block. If you install a gasket designed for a Mark IV block, on a gen V or VI block , the front coolant hole in block will be exposed. The water then enters front...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.