Offshoreonly.com - Search Results

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Black Baja
Showing results 1 to 25 of 500
Search took 0.31 seconds.
Forum: General Q & A
01-01-2017, 10:32 AM
Replies: 94
Views: 8,296
Posted By Black Baja

What head gaskets were used on the motor in...

What head gaskets were used on the motor in question? I have a pair of 540 Merlins that were built in 2000 they still have the original oil lines, filter pad, block adapter and cooler from the...
Forum: General Q & A
12-29-2016, 07:24 AM
Replies: 798
Views: 51,782
Posted By Black Baja

I don't think spending a couple bucks having a...

I don't think spending a couple bucks having a set of heads touched up with a nice valve job little bowl work and a port match is bad money spent. I spent $700 for some bowl work VJ port match and...
Forum: General Q & A
12-25-2016, 05:37 AM
Replies: 8
Views: 821
Posted By Black Baja

X2 and if you are running a mechanical fuel pump...

X2 and if you are running a mechanical fuel pump that has a lot of spring pressure the composite push rods work very well also.
Forum: General Q & A
12-24-2016, 05:01 PM
Replies: 75
Views: 10,497
Posted By Black Baja

I agree with this for the most part....

I agree with this for the most part. Disagreement... If you put a nice set of headers on a 330hp merc in a boat it will net you a big fat 0. In Tim's case with the present cam I think he would get a...
Forum: General Q & A
12-24-2016, 08:55 AM
Replies: 32
Views: 1,916
Posted By Black Baja

Gas or Methanol?

Gas or Methanol?
Forum: General Q & A
12-24-2016, 04:09 AM
Replies: 75
Views: 10,497
Posted By Black Baja

Bingo. And you need a cam in the motor that will...

Bingo. And you need a cam in the motor that will carry the torque through the Rpm range after the motor makes peak torque. The right cam is not going to make the most peak torque. You have to...
Forum: General Q & A
12-22-2016, 05:09 AM
Replies: 32
Views: 1,916
Posted By Black Baja

No no no. Run the oil lines up to the helm and...

No no no. Run the oil lines up to the helm and mount the control valve right by the throttles. I would use the type with a round nob. Like for a garden hose. Heck probably just use garden hose for...
Forum: General Q & A
12-22-2016, 04:22 AM
Replies: 151
Views: 13,713
Posted By Black Baja

There is no change in geometry with different...

There is no change in geometry with different ratio rocker arms. The distance from the trunnion to the valve stays the same. This distance is what influences geometry (longer arm better geometry)....
12-21-2016, 05:42 PM
Replies: 62
Views: 9,345
Posted By Black Baja

Go to your nearest airport and get AV gas. It was...

Go to your nearest airport and get AV gas. It was around $4/gal this summer. Test anywhere from 112-116 octane. And has a little bit of lead in it.
Forum: General Q & A
12-21-2016, 07:49 AM
Replies: 75
Views: 10,497
Posted By Black Baja

Who at Comp gave you this recommendation?

Who at Comp gave you this recommendation?
12-21-2016, 07:35 AM
Replies: 62
Views: 9,345
Posted By Black Baja

When we have a setup that is at it limits on pump...

When we have a setup that is at it limits on pump fuel we add a splash of race gas and make a pull. If power goes up you know there is a potential problem with the tune-up. If it goes down then you...
12-20-2016, 07:01 PM
Replies: 62
Views: 9,345
Posted By Black Baja

Bingo! MMT is not good for your engine and it...

Bingo! MMT is not good for your engine and it does not boost the octane number...
Forum: General Q & A
12-20-2016, 04:21 PM
Replies: 151
Views: 13,713
Posted By Black Baja

Standard cam standard lifters. I believe it was a...

Standard cam standard lifters. I believe it was a Pac 1326. I will check and let you know for sure tomorrow.
Forum: General Q & A
12-20-2016, 09:52 AM
Replies: 151
Views: 13,713
Posted By Black Baja

I think at that point we are going to need to...

I think at that point we are going to need to know what temperature we need to take that measurement at. Elevation and the moons relationship to the earth is going to affect it as well.
Forum: General Q & A
12-20-2016, 04:35 AM
Replies: 151
Views: 13,713
Posted By Black Baja

It may seem like splitting hairs. But remember we...

It may seem like splitting hairs. But remember we are dealing with 16 lifters. So when you start looking at .0001x16= .0016 or .0002x16= .0032 or .0005x16= .008 The numbers start looking a little...
Forum: General Q & A
12-19-2016, 07:27 PM
Replies: 151
Views: 13,713
Posted By Black Baja

Jesel recommends .0018-.0022 clearance on there...

Jesel recommends .0018-.0022 clearance on there liffers
12-17-2016, 07:59 PM
Replies: 260
Views: 31,980
Posted By Black Baja

15,000lb cigarette 15,000lb formula 15,000lb...

15,000lb cigarette 15,000lb formula 15,000lb black thunder. Sounds like you have an obsession for heavy girls...
Forum: General Q & A
12-15-2016, 07:47 PM
Replies: 187
Views: 18,872
Posted By Black Baja

Mike Lewis built a pump gas 565 with the 300...

Mike Lewis built a pump gas 565 with the 300 Ovals and it made over 900hp. If you look at the flow numbers of the 300's they are right in line with the 335's all the way to .700" lift. There have...
Forum: General Q & A
12-15-2016, 06:31 PM
Replies: 187
Views: 18,872
Posted By Black Baja

I think the 325/335's are the worst heads they...

I think the 325/335's are the worst heads they make. I think the 315 or even the 357 would have made more power on Tims.
Forum: General Q & A
12-15-2016, 06:27 PM
Replies: 187
Views: 18,872
Posted By Black Baja

I bet the 300 Ovals would kick the crap out of...

I bet the 300 Ovals would kick the crap out of all the other Afr's on a 540...
Forum: General Q & A
12-15-2016, 07:17 AM
Replies: 187
Views: 18,872
Posted By Black Baja

Hate to b a pain in the azz. But what happens...

Hate to b a pain in the azz. But what happens when we close the Lsa on the 248/256 2*?
Forum: General Q & A
12-15-2016, 06:08 AM
Replies: 187
Views: 18,872
Posted By Black Baja

If you want to spin the motor to 6,000 IN the...

If you want to spin the motor to 6,000 IN the BOAT. You need to look at the numbers from 5,000 to 6,000 the 741 isn't going to make it to 6,000 it will stop dead in it track right where torque and...
Forum: General Q & A
12-13-2016, 07:08 AM
Replies: 187
Views: 18,872
Posted By Black Baja

If you could. That way everyone can see why most...

If you could. That way everyone can see why most of those cams don't have a shot in hell running over 5,000 rpms I think everyone gets caught up in peak numbers and misses how important where peak...
Forum: General Q & A
12-13-2016, 06:53 AM
Replies: 187
Views: 18,872
Posted By Black Baja

Joe, will your software plot a graph?

Joe, will your software plot a graph?
Forum: General Q & A
12-13-2016, 05:35 AM
Replies: 187
Views: 18,872
Posted By Black Baja

O None of the above. But K is getting in the...

O None of the above. But K is getting in the realm.
Showing results 1 to 25 of 500
 


 
Forum Jump

OSO Sponsor
OSO Advertiser
OSO Advertiser
OSO Advertiser
OSO Advertiser
OSO Advertiser

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

OSO Advertiser