Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: mike tkach
Showing results 1 to 25 of 500
Search took 0.12 seconds.
Forum: Wanted
04-05-2021, 09:53 PM
Replies: 3
Views: 230
Posted By mike tkach

if mike does not have one i believe i do.il check...

if mike does not have one i believe i do.il check tomorrow.
Forum: General Q & A
03-19-2021, 09:15 AM
Replies: 76
Views: 2,889
Posted By mike tkach

5 lb increment is wrong and is your problem.never...

5 lb increment is wrong and is your problem.never go less than 15 lb increments on head bolts.
Forum: General Q & A
03-17-2021, 04:40 AM
Replies: 38
Views: 1,340
Posted By mike tkach

imo anything you an do to stabilize the valve...

imo anything you an do to stabilize the valve train is a plus,in a marine endurance engine that sees high rpm,s for a long time it is going to extend the life of the valve springs.it,s amazing how...
Forum: General Q & A
03-10-2021, 05:03 PM
Replies: 26
Views: 945
Posted By mike tkach

most likley the slave soeinoid.

most likley the slave soeinoid.
01-19-2021, 07:59 AM
Replies: 7
Views: 882
Posted By mike tkach

the salt water may have rotted the...

the salt water may have rotted the manifolds&risers causing reversion,or the heads may be rotted where the valve guides press into the heads.i would not run it again till the problem is found because...
01-04-2021, 08:07 AM
Replies: 235
Views: 40,529
Posted By mike tkach

are those steel freeze plugs?

are those steel freeze
plugs?
12-27-2020, 12:46 PM
Replies: 304
Views: 23,493
Posted By mike tkach

il do jail time before il get the shot.

il do jail time before il get the shot.
Forum: Swap Shop
12-22-2020, 07:43 AM
Replies: 16
Views: 2,070
Posted By mike tkach

i would post a picture of one of mine but they...

i would post a picture of one of mine but they are always flying around the world and don,t stop long
enough for a photo shoot,lol.
Forum: Swap Shop
12-21-2020, 06:56 PM
Replies: 16
Views: 2,070
Posted By mike tkach

i have never chartered a citation x but i do own...

i have never chartered a citation x but i do own a couple of them,LOL.
Forum: General Q & A
12-17-2020, 05:30 PM
Replies: 53
Views: 2,457
Posted By mike tkach

yes, i put gen 6 step nose cams in mark 4 blocks...

yes, i put gen 6 step nose cams in mark 4 blocks all the time.you use a gen 6 timing chain&gears and a gm cam retaining plate.i have the gm part number for the plate&bolts in the shop and can list...
Forum: General Q & A
12-16-2020, 06:46 PM
Replies: 53
Views: 2,457
Posted By mike tkach

agree,either one would work.

agree,either one would work.
Forum: General Q & A
12-16-2020, 06:44 PM
Replies: 53
Views: 2,457
Posted By mike tkach

yes step nose gen6.

yes step nose gen6.
Forum: General Q & A
12-16-2020, 05:29 PM
Replies: 53
Views: 2,457
Posted By mike tkach

i think the hp500 efi cam would be a good...

i think the hp500 efi cam would be a good choice,230/236 at .050.598/610 lift 114 lsa.crane cams 169621.with the factory heads and 10.25 to 1 cr i think it will make you smile.i might have one on the...
Forum: Swap Shop
12-14-2020, 08:37 AM
Replies: 3
Views: 587
Posted By mike tkach

patrick,check hit the mailbox this morning.

patrick,check hit the mailbox this morning.
Forum: Swap Shop
12-07-2020, 08:24 PM
Replies: 3
Views: 587
Posted By mike tkach

if you will take 175.00 for it i will send...

if you will take 175.00 for it i will send someone to pick it up.i can pay anyway you want.
Forum: Swap Shop
12-07-2020, 08:18 PM
Replies: 3
Views: 587
Posted By mike tkach

just a fyi,both main&rod journals have been...

just a fyi,both main&rod journals have been ground .010 undersize.this information is based on your measurements.
11-11-2020, 08:18 AM
Replies: 151
Views: 7,454
Posted By mike tkach

what is the list number on the carb?it is stamped...

what is the list number on the carb?it is stamped on the front of the choke horn.
Forum: General Q & A
11-11-2020, 08:09 AM
Replies: 11
Views: 1,226
Posted By mike tkach

unless i read it wrong the op said a 400hp engine...

unless i read it wrong the op said a 400hp engine but did not state what cu in the engine is.
11-02-2020, 10:19 PM
Replies: 10
Views: 1,282
Posted By mike tkach

it should screw right back in the hole it just...

it should screw right back in the hole it just came out of i would think.
10-28-2020, 08:51 AM
Replies: 6
Views: 448
Posted By mike tkach

to me it sounds like the accelerator pump in the...

to me it sounds like the accelerator pump in the carb is not pumping,time for a carb rebuild.
10-27-2020, 10:02 PM
Replies: 29
Views: 1,974
Posted By mike tkach

does it have an electric fuel pump?

does it have an electric fuel pump?
Forum: General Q & A
10-27-2020, 08:59 PM
Replies: 6
Views: 467
Posted By mike tkach

whatever srp sais is what i would do.because it...

whatever srp sais is what i would do.because it is clos
ed cooling i see no reason for xtra piston to wall clearance.i would inc
reas the top&second ring gaps .001 per inch.
Forum: Swap Shop
10-25-2020, 10:57 PM
Replies: 8
Views: 1,086
Posted By mike tkach

location?

location?
10-23-2020, 10:20 PM
Replies: 29
Views: 1,974
Posted By mike tkach

she,s bad azz.glad to see it running.

she,s bad azz.glad to see it running.
Forum: General Q & A
10-16-2020, 09:09 AM
Replies: 79
Views: 5,091
Posted By mike tkach

i must agree with billk,i don,t think the oil is...

i must agree with billk,i don,t think the oil is getting past the rings.the oil on the back side of the intake valves makes me think the oil is coming from the intake tract somehow.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.