Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Gimme Fuel
Showing results 1 to 9 of 9
Search took 0.01 seconds.
Forum: General Q & A
09-18-2020, 07:02 AM
Replies: 28
Views: 838
Posted By Gimme Fuel

Yes those nice rectangular dents in piston say...

Yes those nice rectangular dents in piston say broken ring to me. Almost looks like piece is still imbedded in piston. Take a magnet across the dents and see where it sticks. I've seen this before...
09-01-2020, 10:06 AM
Replies: 880
Views: 211,097
Posted By Gimme Fuel

I did run their syn 80-90w marine gear oil in my...

I did run their syn 80-90w marine gear oil in my 1000 hour bravo drives behind 502mpi on 380 Powerquest with half bottle of Lucas synthetic Stabilizer in each drive. Drained it 3 seasons later (~100...
09-01-2020, 06:51 AM
Replies: 880
Views: 211,097
Posted By Gimme Fuel

Would it be possible to ditch the dry sump system...

Would it be possible to ditch the dry sump system and the few HP that goes with it and change to simple wet sump? Or will that make your oil control issue only worse? Anti-foam additives?
08-17-2020, 10:49 AM
Replies: 17
Views: 568
Posted By Gimme Fuel

Oof. That's not a small amount. That's basically...

Oof. That's not a small amount. That's basically take all tires off and slide in on floor jacks or dollys territory.....Hopefully the concrete floor is very smooth.
Forum: General Q & A
08-06-2020, 02:44 PM
Replies: 31
Views: 2,710
Posted By Gimme Fuel

On my last boat with built engine, I had only one...

On my last boat with built engine, I had only one oil temp gauge, but installed 3 pole switch, and two sensors. One pre-cooler, one after. All I had to do was flip a toggle to see the temperature...
06-29-2020, 09:19 AM
Replies: 22
Views: 1,634
Posted By Gimme Fuel

That is Effing Awesome! All of the...

That is Effing Awesome! All of the show-off-iness at the docks and zero issues shifting/docking at flip of a switch!
Forum: General Q & A
05-13-2020, 01:13 PM
Replies: 11
Views: 605
Posted By Gimme Fuel

When you turn your key to "ON" you should hear...

When you turn your key to "ON" you should hear the fuel pump start running for about 5 seconds which pressurizes the system before you start cranking. That is what he is referring to as the method...
Forum: Checkmate
05-05-2020, 06:30 AM
Replies: 8
Views: 983
Posted By Gimme Fuel

Did he dyno his engine to know what RPM it makes...

Did he dyno his engine to know what RPM it makes peak power? Best bet if you don't know that is to start with original prop he had to establish a baseline and go from there.

I built a 548 for my...
Forum: General Q & A
04-26-2019, 12:49 PM
Replies: 108
Views: 12,044
Posted By Gimme Fuel

After your prompting on other thread, seeing as...

After your prompting on other thread, seeing as you pull vacuum line from FPR and issue cures itself, could you have a collapsed/pinched vacuum line that is closing off and is holding vacuum to...
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.