Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: BillK
Showing results 1 to 9 of 9
Search took 0.01 seconds.
Forum: General Q & A
09-17-2020, 02:11 PM
Replies: 22
Views: 471
Posted By BillK

You are right, cant believe I missed that :( ...

You are right, cant believe I missed that :( That is where they like to burn through too.
Forum: General Q & A
09-17-2020, 12:04 PM
Replies: 22
Views: 471
Posted By BillK

Tom, I have seen plenty of engines over the...

Tom,
I have seen plenty of engines over the years that have run just fine for a loooong time with marks like that. I would almost say leave it alone.

That being said about the only way you...
Forum: General Q & A
09-13-2020, 07:30 PM
Replies: 5
Views: 176
Posted By BillK

The holes will be different from damper to damper...

The holes will be different from damper to damper due to manufacturing tolerances. The only way to see if the mark is correct is to find TDC with a TDC stop and check it. Neither of those look like...
Forum: General Q & A
09-12-2020, 02:09 PM
Replies: 12
Views: 435
Posted By BillK

Tom, Those gaskets really should not need...

Tom,

Those gaskets really should not need any additional sealer. The black coating is a sealer in itself. When you did the freshen up were the heads resurfaced ? Where exactly are the gaskets...
Forum: General Q & A
09-08-2020, 01:16 PM
Replies: 9
Views: 466
Posted By BillK

That was the incorrect length bolt for the...

That was the incorrect length bolt for the starter. The block has a small counterbore where the bolt goes in. The knurled portion of the bolt goes into that counterbore and keeps the starter from...
Forum: General Q & A
08-15-2020, 07:36 PM
Replies: 3
Views: 175
Posted By BillK

Cant help you with your marbles but if the engine...

Cant help you with your marbles but if the engine calls for 87 that's what you should be running. It will probably run better and use less fuel.
Forum: General Q & A
08-04-2020, 05:52 AM
Replies: 18
Views: 930
Posted By BillK

You need to stop right now and find out where...

You need to stop right now and find out where that water came from. Dont run the engine again until you find the problem, period. Every time you try to start it with water in a cylinder you are...
Forum: General Q & A
06-29-2020, 10:41 AM
Replies: 15
Views: 963
Posted By BillK

Blocks with incorrect casting numbers are a lot...

Blocks with incorrect casting numbers are a lot more common than guys realize. When you see them all day every day you stop worrying about it. As far as the manifolds go they are probably just...
Forum: General Q & A
06-08-2020, 08:11 PM
Replies: 7
Views: 678
Posted By BillK

If the crankshaft was standing straight up on the...

If the crankshaft was standing straight up on the floor and you looked down on it are there any numbers on the front of the front counterweight ? That is where most manufacturers put their numbers....
Showing results 1 to 9 of 9


 
Forum Jump

OSO Sponsor
OSO Advertiser
OSO Advertiser
OSO Advertiser
OSO Advertiser
OSO Advertiser

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

OSO Advertiser