Offshoreonly.com - Search Results

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: fbc25el
Showing results 1 to 15 of 15
Search took 0.00 seconds.
Forum: General Q & A
07-22-2021, 03:59 PM
Replies: 12
Views: 661
Posted By fbc25el

If all the plugs look good I would take a good...

If all the plugs look good I would take a good look at the intake manifold gasket .
Forum: General Q & A
07-18-2021, 08:37 AM
Replies: 54
Views: 2,202
Posted By fbc25el

Most of the bad ass sounding boat's have a well...

Most of the bad ass sounding boat's have a well though out engine plan. They just don't throw a cam in them.
07-17-2021, 01:44 PM
Replies: 35
Views: 1,288
Posted By fbc25el

check your plug wires. firing order

check your plug wires. firing order
Forum: General Q & A
06-20-2021, 05:39 PM
Replies: 8
Views: 439
Posted By fbc25el

I would send them to CMI and have them modify...

I would send them to CMI and have them modify them. I had mine done a while back.
05-06-2021, 06:06 AM
Replies: 45
Views: 3,060
Posted By fbc25el

They list as 3 circuit 1050 cfm. 3 circuit do not...

They list as 3 circuit 1050 cfm. 3 circuit do not work well in a boat app. You can convert them to 2 circuit but I don't know how much you want to git in to.
Forum: General Q & A
03-11-2021, 06:41 AM
Replies: 42
Views: 2,542
Posted By fbc25el

Try using a piston stop. Dwell time at the top...

Try using a piston stop. Dwell time at the top could be giving some bad numbers.
Forum: General Q & A
03-09-2021, 07:56 AM
Replies: 10
Views: 777
Posted By fbc25el

I torque mine to 75# with ARP lube. Aluminum...

I torque mine to 75# with ARP lube. Aluminum heads.
Forum: General Q & A
03-08-2021, 04:57 AM
Replies: 24
Views: 1,592
Posted By fbc25el

Hold my beer and watch this!

Hold my beer and watch this!
Forum: General Q & A
03-05-2021, 05:59 AM
Replies: 24
Views: 1,514
Posted By fbc25el

I had the same problem. I just put the bolt in...

I had the same problem. I just put the bolt in with the nut on the top side of the guide plate.
Forum: General Q & A
03-04-2021, 06:19 AM
Replies: 24
Views: 1,514
Posted By fbc25el

I think you are going to need to install the...

I think you are going to need to install the guide plates to control the push rod . Too many angles working as the valve opens.
Forum: General Q & A
03-03-2021, 12:09 PM
Replies: 24
Views: 1,514
Posted By fbc25el

Make sure your guide plates are keeping the...

Make sure your guide plates are keeping the pushrod and the rocker centered ( in line ) with the valve tip.
Forum: General Q & A
03-03-2021, 06:04 AM
Replies: 24
Views: 1,514
Posted By fbc25el

I went through the same thing. The only thing I...

I went through the same thing. The only thing I came up with is if you don't get the dial indicator right in line with the valve stem you will get a false reading. AFR heads have a 2* angle on them....
Forum: General Q & A
09-17-2020, 12:11 PM
Replies: 36
Views: 2,620
Posted By fbc25el

Looks like the ring land broke. Was there a...

Looks like the ring land broke. Was there a chance it ran lean?
Forum: General Q & A
07-02-2020, 10:47 AM
Replies: 15
Views: 1,101
Posted By fbc25el

Does it have a transfer slot restrictor, Is the...

Does it have a transfer slot restrictor, Is the idle feed restrictor in the lower position, Is it a 2or3 circuit.
Forum: General Q & A
07-02-2020, 06:37 AM
Replies: 15
Views: 1,101
Posted By fbc25el

Are you sure its a lean problem ?

Are you sure its a lean problem ?
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.