Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: JCCRAZY
Showing results 1 to 25 of 83
Search took 0.02 seconds.
Today, 10:17 AM
Replies: 43
Views: 1,614
Posted By JCCRAZY

Rot

On where your hose is coming through the stringer that may not be rot. Formula didn't always finish up that pass through cleanly. If it is rot its a good time to pull the motors and go over...
Today, 10:14 AM
Replies: 43
Views: 1,614
Posted By JCCRAZY

Pulling

If the boat is pulling you most likely have a bad gimble. You mentioned it being very easy to move, in one direction, so make sure and check the gimble pins and steering ram. Typically a worn TRS...
Today, 09:29 AM
Replies: 43
Views: 1,614
Posted By JCCRAZY

Water in hull

357's have an issue with draining water from the front of the boat. There should be a bilge pump under the cabin step. Make sure it is operating. The water from any leaks is supposed to drain from...
Today, 09:15 AM
Replies: 43
Views: 1,614
Posted By JCCRAZY

Help

I totally understand your situation and I'm with Griff. There are a lot of "boaters" that know nothing about boats. I have completely redone two 357"s. My current one is and an '89 that has been so...
Forum: Wanted
08-24-2019, 03:30 PM
Replies: 16
Views: 1,650
Posted By JCCRAZY

no project

I will be selling my 357 Formula that I'm just finishing up onhttps://cimg7.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/180x120/357_profile_57c2c7ff2b0c2f6947094945d01a3044adf2890b.jpg
. I have a...
08-24-2019, 09:44 AM
Replies: 4
Views: 359
Posted By JCCRAZY

I'm not a cam guy but according to builder the...

I'm not a cam guy but according to builder the cam is several steps different than the 420/425 factory cam. He also says we can easily change to the bigger one if I'm not satisfied. I didn't want to...
08-23-2019, 10:43 AM
Replies: 4
Views: 359
Posted By JCCRAZY

Desktop dyno users and "been there, built that" estimators

My engine builder just finished a set of engines for my Formula. I needed them to be "island gas" friendly but I couldn't get a dyno time scheduled prior to installs so I'm looking for estimated hp....
Forum: Swap Shop
05-07-2019, 10:43 AM
Forum: Swap Shop
05-03-2019, 12:44 PM
Replies: 14
Views: 3,300
Posted By JCCRAZY

Not a problem 954-573-0262 -

Not a problem
954-573-0262


-
Forum: Swap Shop
05-01-2019, 03:43 PM
Forum: Swap Shop
04-29-2019, 01:23 PM
Replies: 14
Views: 3,300
Posted By JCCRAZY

https://cimg4.ibsrv.net/gimg/www.offshoreonly.com-...

https://cimg4.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/480x640/img_1303_ef84f13e2347cd8e5dd6006bae9486f93cde110f.jpg...
Forum: Swap Shop
04-28-2019, 10:47 AM
Replies: 14
Views: 3,300
Posted By JCCRAZY

The water jackets are in quite good condition....

The water jackets are in quite good condition. There is slight corrosion at the thermostat outlets which you can see in the current pictures.

There are no carburetors with the package.
Forum: Swap Shop
04-26-2019, 08:47 PM
Replies: 14
Views: 3,300
Posted By JCCRAZY

Accepting reasonable offer

Willing to negotiate for reasonable offer
Forum: Swap Shop
04-12-2019, 03:09 PM
Replies: 14
Views: 3,300
Posted By JCCRAZY

Fresh 525SC's with accessories

To clarify for those who have asked I will include shipping to lower 48 at $3400
Forum: Swap Shop
03-27-2019, 04:10 PM
Replies: 14
Views: 3,300
Posted By JCCRAZY

Pics

https://cimg6.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/1500x2000/3f33fe0e_bce2_40f5_bf19_c42629e12af8_a3758a196addb7d8bbb0e85fcaaf13e573b5b1cd.jpeg...
Forum: Swap Shop
03-17-2019, 01:16 AM
Forum: Swap Shop
03-12-2019, 04:05 PM
Replies: 14
Views: 3,300
Posted By JCCRAZY

Pair of Mercruiser SC Superchargers fresh from The Blower Shop

Selling Pair of Mercruiser SC (OEM Mercruiser Weiand 177's) fresh from The Blower Shop, never installed. They have all new bearings and seals and the rotors were modified with TEFLON edging. Input...
Forum: Swap Shop
03-06-2019, 08:10 PM
Replies: 20
Views: 1,736
Posted By JCCRAZY

All sold except mufflers

All sold except mufflers
Forum: Swap Shop
02-28-2019, 08:57 AM
Replies: 20
Views: 1,736
Posted By JCCRAZY

Adapter plates are sold

Adapter plates are sold
Forum: Swap Shop
02-19-2019, 10:24 AM
Forum: Swap Shop
02-17-2019, 09:30 AM
Replies: 20
Views: 1,736
Posted By JCCRAZY

I apologize, I just spoke to my builder and yes...

I apologize, I just spoke to my builder and yes they are forged pistons. #2399's .095 dome. Factory set up.
Forum: Swap Shop
02-16-2019, 01:44 PM
Replies: 20
Views: 1,736
Posted By JCCRAZY

can be switched to forged pistons if deal done...

can be switched to forged pistons if deal done prior to build finishing
Forum: Swap Shop
02-16-2019, 01:43 PM
Replies: 20
Views: 1,736
Posted By JCCRAZY

stock pistons, forged crank and big (7/16) rods

stock pistons, forged crank and big (7/16) rods
Forum: Swap Shop
02-15-2019, 09:09 PM
Replies: 20
Views: 1,736
Posted By JCCRAZY

intakes are sold

intakes are sold
Forum: Swap Shop
02-12-2019, 12:54 PM
Replies: 20
Views: 1,736
Posted By JCCRAZY

420's are 454 ci

420's are 454 ci
Showing results 1 to 25 of 83
 


 
Forum Jump

OSO Sponsor
OSO Advertiser
OSO Advertiser
OSO Advertiser
OSO Advertiser
OSO Advertiser
OSO Advertiser