don't know where to start?
#1
Thread Starter
Registered
Joined: Oct 2011
Posts: 195
Likes: 0
From: mentor ohio
Im doing a project boat and I have never run the boat before so I don't have a clue where to start with a prop.
The boat is a 1990 Profile gt 26 it has a small pad and I am running a 475/500 hp big block with a bravo 1 with a 136 drive it has a Bobs nose cone with a low water pick up on it. Any help would be great.
Thanks Keith
The boat is a 1990 Profile gt 26 it has a small pad and I am running a 475/500 hp big block with a bravo 1 with a 136 drive it has a Bobs nose cone with a low water pick up on it. Any help would be great.
Thanks Keith
#3
Thread Starter
Registered
Joined: Oct 2011
Posts: 195
Likes: 0
From: mentor ohio
#4
Registered
Joined: Apr 2009
Posts: 1,852
Likes: 1
From: Denmark and hopefully some place nice
It depends on where the power is made. Even if the motor spins "only" 5200 max, a 26" (25") B1 would put it at 80 mph with a 12% slip. I think that number is too high with that power. I would prop for about 73-75 and go from there. Overall, when stuff is new, baseline testing is needed. Either 23" Rev4 or Bravo1 24" if spinning 5200 and up. The Rev4 has an overall better lift than the B1, so that would be my first choice.
Last edited by A.O. Razor; 12-15-2011 at 07:10 AM.
#5
Thread Starter
Registered
Joined: Oct 2011
Posts: 195
Likes: 0
From: mentor ohio
Keith. Powerplay J was talking about the Mercury Bravo1 prop.
It depends on where the power is made. Even if the motor spins "only" 5200 max, a 26" (25") B1 would put it at 80 mph with a 12% slip. I think that number is too high with that power. I would prop for about 73-75 and go from there. Overall, when stuff is new, baseline testing is needed. Either 23" Rev4 or Bravo1 24" if spinning 5200 and up. The Rev4 has an overall better lift than the B1, so that would be my first choice.
It depends on where the power is made. Even if the motor spins "only" 5200 max, a 26" (25") B1 would put it at 80 mph with a 12% slip. I think that number is too high with that power. I would prop for about 73-75 and go from there. Overall, when stuff is new, baseline testing is needed. Either 23" Rev4 or Bravo1 24" if spinning 5200 and up. The Rev4 has an overall better lift than the B1, so that would be my first choice.
#6
Registered

Joined: Dec 2007
Posts: 714
Likes: 4
i agree with A.O. Razor use a smaller prop . i have a 24baja with a 136drive . i use a 24bravo one prop.truning it at 5800 and i have 718hp 540dart motor . prop your boat to the redline on your motor if it is 5200 then make shore you put the prop that make it spin that good luck
#8
Registered
Joined: Jul 2008
Posts: 4,496
Likes: 1
From: Lk. st. Clair MI
Keith. Powerplay J was talking about the Mercury Bravo1 prop.
It depends on where the power is made. Even if the motor spins "only" 5200 max, a 26" (25") B1 would put it at 80 mph with a 12% slip. I think that number is too high with that power. I would prop for about 73-75 and go from there. Overall, when stuff is new, baseline testing is needed. Either 23" Rev4 or Bravo1 24" if spinning 5200 and up. The Rev4 has an overall better lift than the B1, so that would be my first choice.
It depends on where the power is made. Even if the motor spins "only" 5200 max, a 26" (25") B1 would put it at 80 mph with a 12% slip. I think that number is too high with that power. I would prop for about 73-75 and go from there. Overall, when stuff is new, baseline testing is needed. Either 23" Rev4 or Bravo1 24" if spinning 5200 and up. The Rev4 has an overall better lift than the B1, so that would be my first choice.
#9
I would probably start with 24 Bravo 4 blade. It should run about a 70-75mph if the slip is correct.
Being an older boat, the drive might be set pretty deep and it may actually like a Mirage Plus.
The 24 Bravo should get you decent baseline though.
Being an older boat, the drive might be set pretty deep and it may actually like a Mirage Plus.
The 24 Bravo should get you decent baseline though.



