ENGINE BUILDER MAG.COM High Performance Boating Market
09-04-2013 | 02:54 PM
#1
Thread Starter
Platinum Member
Joined: Jul 2008
Posts: 931
Likes: 0
From: Little River SC
ENGINE BUILDER MAG.COM High Performance Boating Market
http://www.enginebuildermag.com/Arti...ng_market.aspx
Just received my copy today. See the market is getting some attention and may help boost the sport. I see Chris Sunkin, is the contributing editor.
Just received my copy today. See the market is getting some attention and may help boost the sport. I see Chris Sunkin, is the contributing editor.
09-04-2013 | 03:04 PM
#2
Banned
Joined: Jul 2011
Posts: 9,594
Likes: 45
From: Ft. Worth TX
I got it in the mail also. So my question is why Chris Sunkin for the report in EB magazine. I have no idea who he is except he was up here at one time and left to start seriousoffshore.com
Seems the name comes up, thrown around a lot up here as a dog?
A couple years ago Engine Builder mag did a report from Bob Madera - Marine Kinetics from New York.
Seems the name comes up, thrown around a lot up here as a dog?
A couple years ago Engine Builder mag did a report from Bob Madera - Marine Kinetics from New York.
Last edited by BUP; 09-04-2013 at 03:22 PM.
09-04-2013 | 03:21 PM
#4
Gold Member
Joined: Jun 2006
Posts: 5,117
Likes: 959
From: Seaford, VA
Here we go....................
I am guessing 297 responses. Almost 10 pages if you're setting is 30 responses per page. If this stays on the front page until after November 1 I am upping my guess to 423 responses.
I am guessing 297 responses. Almost 10 pages if you're setting is 30 responses per page. If this stays on the front page until after November 1 I am upping my guess to 423 responses.
09-04-2013 | 03:24 PM
#5
Registered
Joined: Aug 2008
Posts: 774
Likes: 1
From: Wild n Reckless From North Texas
Chris Sunkin is a 40-year performance boating enthusiast and the founder of seriousoffshore.com, a web forum serving this market. Chris is an experienced machinist and builder and has built and rigged numerous high-performance boat powertrains.
09-04-2013 | 03:30 PM
#6
SORE MEMBER
Joined: Apr 2004
Posts: 6,984
Likes: 1
From: 29°50'49.74"N 95° 5'17.55"W.......TEXAS
Damn! He has been busy.
09-04-2013 | 04:04 PM
#7
Platinum Member
Joined: Jun 2004
Posts: 7,317
Likes: 1,032
From: frankenmuth michigan
Oh this is some funny azz shiit, here is a QUOTE:
I’ve seen sections of -12 3,500 psi hose affixed to a shiny red anodized AN adapter on a pump or cooler. The rigger failed to notice that the passage through that section was a third the size of the rest of his plumbing.
He saw this in the pictures I posted in "my oil problems from stock hardware" thread that I posted on here years ago and then ASKED me to post it on serious offshore before he became a pariah around here!!! I guess its not a lie though, he DID see it, just it was in MY pictures I posted, LMAO, Smitty
I’ve seen sections of -12 3,500 psi hose affixed to a shiny red anodized AN adapter on a pump or cooler. The rigger failed to notice that the passage through that section was a third the size of the rest of his plumbing.
He saw this in the pictures I posted in "my oil problems from stock hardware" thread that I posted on here years ago and then ASKED me to post it on serious offshore before he became a pariah around here!!! I guess its not a lie though, he DID see it, just it was in MY pictures I posted, LMAO, Smitty
09-04-2013 | 04:06 PM
#8
Platinum Member
Joined: Jun 2004
Posts: 7,317
Likes: 1,032
From: frankenmuth michigan
Oh this is EVEN cooler, in the comment section:
Sunkin built the motors in all 6 of my 41 Apache's. 927 hours on 1500hp bad azz blower motors and I haven't even had to change the oil yet!!!
Sunkin built the motors in all 6 of my 41 Apache's. 927 hours on 1500hp bad azz blower motors and I haven't even had to change the oil yet!!!
09-04-2013 | 05:20 PM
#10
Registered
Joined: Jan 2004
Posts: 4,480
Likes: 43
From: Tennessee
Oh this is some funny azz shiit, here is a QUOTE:
I’ve seen sections of -12 3,500 psi hose affixed to a shiny red anodized AN adapter on a pump or cooler. The rigger failed to notice that the passage through that section was a third the size of the rest of his plumbing.
He saw this in the pictures I posted in "my oil problems from stock hardware" thread that I posted on here years ago and then ASKED me to post it on serious offshore before he became a pariah around here!!! I guess its not a lie though, he DID see it, just it was in MY pictures I posted, LMAO, Smitty
I’ve seen sections of -12 3,500 psi hose affixed to a shiny red anodized AN adapter on a pump or cooler. The rigger failed to notice that the passage through that section was a third the size of the rest of his plumbing.
He saw this in the pictures I posted in "my oil problems from stock hardware" thread that I posted on here years ago and then ASKED me to post it on serious offshore before he became a pariah around here!!! I guess its not a lie though, he DID see it, just it was in MY pictures I posted, LMAO, Smitty
