More Stuff from the Garage!
 

Time to get rid of all the extra parts lying around. I have alot of parts from several projects that are taking up too much space and tying up too much cash. I will get pics posted tomorrow of most of it. Any interests please let me know before it all goes on ebay. All this stuff is fresh water used. All in good useable condition. NO JUNK! All items are plus shipping or you can pick it up in Philadelphia, PA. 19136

1. 2- B&M 250 marine blowers complete from intakes to air cleaners, dual carbs on each. $2500, each.OBO
3. 1- KPM strainer, will handle 2 engines. $400.
4. 1- Merc. trim pump work fine with mounts. new motors good reservoir. $150.
5. 1- Bravo 1 hub for STD 1" shaft, solid HP. $50.
6. 2- Marine machine, Bravo 1 wing plates SS for twins $400. for the pairOBO
7. 2- MSD Boost Timing Master modules $100. Each
10. 2- Drive temp parts. thru hulls and gauges, needs senders and wires. $75. for the pair.
11. 2- Crane Cams BBC stud girdle set ups. Used but great condition. With locks $125.ea.
12.SOLD 2- Merlin "X" Intake manifolds New for Dominator carbs I has dyno time only $350.ea.
13. 1- Mercruiser factory remote oil filter set up w/ hoses and bracket. $75.
14. 1- Latham Bravo tie bar saddle, New. $50.
15. 2- Bravo/Alpha transom inner plates. New, $75. ea.
17. 1- 468 cu.in. BBC short block. Aprox 40 hours. Forged internals, 8.5:1 comp with oil pan flywheel and balancer. No cam. $1500.
20. 2- Polished Dominator throttle cable brackets. New. With clips, $30. each.
23. 2- Prop Socs for a pair of 3 blade props. $20. for the pair.
24.SOLD Livorsi GPS 120mph Speedo setup complete with 3 3/8" speedo, antenna and recall switch. Antenna new last season. All white, $350.

Pics from the Garage!
 

More pics coming!

More Pics!
 

Here they are!

PM sent for Oil Press Guages

I need the strainer.9. 1- Livorsi Sea strainer, NEW, red top. $250 PLEASE CONTACT ME FOR ARRANGEMENTS,Thanks ,Bob

Will those MSD boxes work with TB 1V ignitions ? I am looking for a little extra spark for my stock set up.
Thanks,
John

Hey John, I''m not sure if they are what you need. Take a look on MSD site and maybe you can get the right information you need on them. I think they are for timing adjustments but I'm not really sure. Let me know what you find out.

pm sent.

got any pics of the stud girdles ?

468 Bbc
 

What generation is the block? Does it need work? Why is the cam out of it? I'm in Northern Maryland. Thanks

It's a genIV block. No it doesn't need anything. I sold the top end off of it with the cam, heads, lifters, intake and carb etc. It has maybe 40 hours on it and ran perfect before I took them out to go with a new set of 540's I sold the other complete engine and the top to this one. It's just sitting here getting in the way. Someone might as well have some fun with it. Give me a call in Philly if you have any questions. Bill Redmond 215-768-4172

More pics of the stuff!
 

I have more coming!

Pm sent for a trim pump

Can you send me a pic of the bellhousing

can you post a pic ot the remote oil filter setups

Here's pics of the bell housing and oil filter remotes and a few other things.

oil remote have a thermostat??Thanks

No these are the older factory units. I have 2 set ups, one has an oil cooler and one doesn't They mount the filter up on the exhaust manifold.

Thanks the strainer is as promised.

I'll take the bravo bellhousing and all 4 red speaker grilles for asking price if you pick up shipping. Ground to 48083, business.

message sent on the starter
please let me know
thanks

Thanks guys! Here's a few more pics. I updated the sold items at the first post.

Payment sent on the bellhousing and speaker grilles. thanks again.

Added GPS Speedo and strainer pics.

Blower pics

updated list and lowered some prices

Do the manifolds have the brass inserts

Yes, the intakes have the brass inserts. They are new, one has dyno time only.

ttt

will those stainless pieces fit an alpha one? or are they bravo only?im looking to build a hydraulic steering system for an alpha one

Not sure if they will fit or not. They mount to the 2 top bolts of the drive. Bolts measure 6" across and 2" up and down on centers if that helps?

I'm interested in 1 of the B&M supercharger setups. These are for standard deck, rectangular port, correct?
What carbs are on them? And, who set them up for the blowers?

Intakes sold. One blower sold, I think? Sun, did you still have an interest in the other one?

1- Mercruiser factory remote oil filter set up w/ hoses and bracket. $75. ....... what gen is that from? I need a 4