BBC CMI Sport Tubes - stainless - polished - lots of pics
08-05-2013, 09:27 PM
#1
Registered
Thread Starter
BBC CMI Sport Tubes - stainless - polished - lots of pics
Used set of CMI Sport tubes. I'm indecisive, and I want to run my Corsa system again.
No tails, no clamps or gaskets are included.
I bought these, hung them on the wall, and have never used them. Fits 454/502. I was told that they will work with 496, but mod the shifter cable mounts a little.
Asking $1,500. Located in League City, Tx. South of the Houston area.
I bought these from another board member on here or from the Facebook group, any questions, just ask.
No tails, no clamps or gaskets are included.
I bought these, hung them on the wall, and have never used them. Fits 454/502. I was told that they will work with 496, but mod the shifter cable mounts a little.
Asking $1,500. Located in League City, Tx. South of the Houston area.
I bought these from another board member on here or from the Facebook group, any questions, just ask.
08-07-2013, 02:15 PM
#4
Registered
Offer
Used set of CMI Sport tubes. I'm indecisive, and I want to run my Corsa system again.
No tails, no clamps or gaskets are included.
I bought these, hung them on the wall, and have never used them. Fits 454/502. I was told that they will work with 496, but mod the shifter cable mounts a little.
Asking $1,500. Located in League City, Tx. South of the Houston area.
I bought these from another board member on here or from the Facebook group, any questions, just ask.
No tails, no clamps or gaskets are included.
I bought these, hung them on the wall, and have never used them. Fits 454/502. I was told that they will work with 496, but mod the shifter cable mounts a little.
Asking $1,500. Located in League City, Tx. South of the Houston area.
I bought these from another board member on here or from the Facebook group, any questions, just ask.
08-07-2013, 02:18 PM
#5
Registered
Will you take $1,000. I will pay for shipping if you are interested. Please note that I'm taking a chance if they leak and also I have to get rings and make custom pipes which will cost a pretty penny. Thanks for considering!
08-08-2013, 10:16 AM
#6
Registered
Thread Starter
I pressure tested them last night in a kiddy pool. They were good until 30-35psi . . . but after 40 there are pin holes on the flanges, and another at the collector. Funny part, it's at the welds on each spot, not the tube.
I'll pressure test them again after the repairs are done and post up again.
I'll pressure test them again after the repairs are done and post up again.
08-09-2013, 06:09 PM
#7
Registered
Thread Starter
lock this thread up, I'm not going to pass along junk that was sold to me.
my fault for not checking them when I received them.
His fault for listing parts with no issues.
I took the headers to two local fab shops, and they said that they were beyond repairs.
tried filing a dispute with paypal, but it's been past 45 days
I've sent the previous seller emails, and he has not replied yet.
my fault for not checking them when I received them.
His fault for listing parts with no issues.
I took the headers to two local fab shops, and they said that they were beyond repairs.
tried filing a dispute with paypal, but it's been past 45 days
I've sent the previous seller emails, and he has not replied yet.
08-09-2013, 06:33 PM
#8
Fast Singles Club
Gold Member
iTrader: (8)
lock this thread up, I'm not going to pass along junk that was sold to me.
my fault for not checking them when I received them.
His fault for listing parts with no issues.
I took the headers to two local fab shops, and they said that they were beyond repairs.
tried filing a dispute with paypal, but it's been past 45 days
I've sent the previous seller emails, and he has not replied yet.
my fault for not checking them when I received them.
His fault for listing parts with no issues.
I took the headers to two local fab shops, and they said that they were beyond repairs.
tried filing a dispute with paypal, but it's been past 45 days
I've sent the previous seller emails, and he has not replied yet.
08-09-2013, 10:06 PM
#10
Registered
Thread Starter
returned !
