Offshoreonly.com
Page 3 of 4
1
2
3
4
Show 40 post(s) from this thread on one page

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   Swap Shop (https://www.offshoreonly.com/forums/swap-shop-253/)
-   -   PSI 206B Blowers/Intercoolers kits (https://www.offshoreonly.com/forums/swap-shop/306486-psi-206b-blowers-intercoolers-kits.html)

endeavor1 12-22-2013 03:09 PM
Originally Posted by Coolerman (Post 4045983)
I Got PMS right now but Here are a couple pics with measurements. I plan to go take some midol and drink some fruity wine coolers to calm me down. .
Very informative Saxman....:lolhit: All bs aside though, it's pretty cool that you can walk to your garage and find that kind of hardware.

endeavor1 12-22-2013 03:10 PM
Originally Posted by Velocity Vector (Post 4046002)
I call that dik length.
Quit dicking around here KC and get your OE finished!!! Lol. Merry Christmas bud

Coolerman 12-22-2013 05:33 PM
Originally Posted by Velocity Vector (Post 4046002)
I call that dik length.
lmao, After I saw your comment, I had to double check to make sure I didn't post the wrong pics!

kreed 12-22-2013 06:07 PM
Originally Posted by SS930 (Post 4045421)
Can you please PM me the total blower height (from where it would sit on the IC to where the base of the carb(s) would sit)? TY...
WTF????? The Donzi 16 doesn't need these!

SS930 12-22-2013 07:28 PM
So they are 12" to the top of the dominator adapter plate? What is the IC thickness?

Thanks!

Coolerman 12-22-2013 07:34 PM
Originally Posted by SS930 (Post 4046171)
So they are 12" to the top of the dominator adapter plate? What is the IC thickness?

Thanks!
There are two plates on top of the PSI. The first plate is used to cut your inlet hole(s) to the rotors (10.75" to the top of this plate, what is normally referred to as the top of the blower). Then you add the carb adapter plate on top of that, which can be vary in thicknesses, depending on if you make your own, or who's you buy.

The intercooler case is 5". The intercoolers Doug bought from us also have an integrated PSI adapter plate. Here are some more specs and pics on our coolers www.pfintercoolers.com

SS930 12-22-2013 07:34 PM
Originally Posted by kreed (Post 4046123)
WTF????? The Donzi 16 doesn't need these!
I need to run with the Checkmate the TG's this season... I'm thinking quad rotor PSI on the LS1 should come close! :bunnydance:

SS930 12-22-2013 07:42 PM
Originally Posted by Coolerman (Post 4046173)
There are two plates on top of the PSI. The first plate is used to cut your inlet hole(s) to the rotors (10.75" to the top of this plate, what is normally referred to as the top of the blower). Then you add the carb adapter plate on top of that, which can be vary in thicknesses, depending on if you make your own, or who's you buy.

The intercooler case is 5". The intercoolers Doug bought from us also have an integrated PSI adapter plate. Here are some more specs and pics on our coolers www.pfintercoolers.com
Maybe I should have asked, what's the dimension from the base of the IC to the top of the dominator adapter plate for this exact setup that's being listed here??? I need to check my clearances... Thanks

Coolerman 12-22-2013 07:50 PM
1 Attachment(s)
Originally Posted by SS930 (Post 4046174)
I need to run with the Checkmate the TG's this season... I'm thinking quad rotor PSI on the LS1 should come close! :bunnydance:
:drink:

Coolerman 12-22-2013 07:51 PM
Originally Posted by SS930 (Post 4046177)
Maybe I should have asked, what's the dimension from the base of the IC to the top of the dominator adapter plate for this exact setup that's being listed here??? I need to check my clearances... Thanks
Should be 11.5" including the carb adapter, but that's assuming Dougs carb adapter is 3/4" thick. You'll have to verify with Doug.


All times are GMT -5. The time now is 01:55 AM.
Page 3 of 4
1
2
3
4
Show 40 post(s) from this thread on one page


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.