3x EFI for tall deck motors
 

I have 3 complete EFI systems for sale 4,000.00 each. This includes all the below or everthing you need.
Intakes customized by Wilson intakes for tall deck and matched ported to Brodix 332 oval port heads
Intakes, fuel rails, Injectors, MSD or GM Oil pump drives,Arizona billet TB, all sensors, Computers and wire harnesses, Flame arestors.
These have about 10 hrs on them and made 750HP on mild 604CI motors.
Ken

I will send new top plates so they can say what ever someone want on them.

Are you parting the boat out?

No I’m going back to carbs. With 3 EFI systems I’m running into ground interference. This could be fixed by running separate grounds to each motor or just switch back to carbs. I'm going to keep the boat so I decided to do the easier of the two.
Ken

These are still in the boat and running if anyone wants to see and hear them.

what base intake manifold are you using?

I believe it's an orange one.

These cost me just over 7K per motor. They are used by Potter Racing and Innovation for there Mil apps.
Ken

Awesome set up but would look a little out of place on my Baja. Separate grounds doesn't sound that hard to do in order to keep them.

when your paying someone to do it is. I have very limited space to work around 3 motors.

Just pulled off the boat so here are more photos.[ATTACH=CONFIG]516360[/ATTACH][ATTACH=CONFIG]516361[/ATTACH][ATTACH=CONFIG]516362[/ATTACH]

I'm sad to see you give up on them. Did you get the drive issue on the boat sorted out?

I do not know if it was a drive issue or a motor issue. One of the motors was losing its fire so it may have been dragging the drive creating this problem.
I have now found the EFI problem I was having with that motor also. The ECU ground was cut so it was never grounded. I’m not going to use the EFI since I have already purchased my Intakes and carbs.
Ken

These would make nice upgrades on the 525 Merc's. I may break these down and sell the Tec-3R's separately.

What ecm's come with these? Also what size injectors?

Bocsh 50LB Electromotive Tec-3R with all extra long plug in harnesses.
Thanks Ken

Do u know who tunes those ecm's?

I just noticed you are local. I have a guy Ricky in Annapolis. You can come by and take a look at everything if you like.
or call my office 301-218-7920 E 201
Thanks Ken

Also the tunning is going to be very little required as they are BBC and already tuned. maybe adjust the fuel if your motors are smaller.
Ken

I'd have to use bigger injectors and get a tune but ill give you a call tomorrow.

What size motors are you running that would require larger injectors?
I was told at 3bar the 403's have enough flow to support 110HP a piece thats 880HP
Ken

I also wanted to note there is plenty of aluminum left to port for rectangle ports or larger ovals.
Ken

Can I put my 10/71`s right on top ?? lol :D
Nice peices

No but she would look good on top:)

I can also supply with standard deck height intake bottoms since these are two piece intakes.
Ken

Ok I had a couple ask about splitting these up so yes I will sell the electronic packages separate from the intake assemblies.
Thanks Ken

These are back up for sale price reduced to 3500 each setup complete.

how much taller than a 500 efi intake is this set up

The total hight is 12-1/2" if setting on a table to the top.

How much for one of the systems minus the electronics?

These are back up for sale 2500 each.
Ken

[QUOTE=ken sampson;4056155]I have 3 complete EFI systems for sale 2,500 each. This includes all the below or everthing you need.
Intakes customized by Wilson intakes for tall deck and matched ported to Brodix 332 oval port heads
Intakes, fuel rails, Injectors, MSD or GM Oil pump drives,Arizona billet TB, all sensors, Computers and wire harnesses, Flame arestors.
These have about 10 hrs on them and made 750HP on mild 604CI motors.
Ken

New Price 2500 each.

I might be interested in one of the setups i have a 572 in the shop that would look good on,do you have the software to tune how old are the ecms

How much do you want for just an ecm?

What CFM are the TB