Complete ready to run engine 1071 blower 502 BBC pumpgas
Here is a Complete engine, fresh rebuild still on the Dyno cart.
The engine was built buy Garry Grimes twister engines out of Atlanta Ga (he builds MANY successful offshore engines) It is a 502 big block chevy Intake to oilpan, with distributer and fuel pump. -Forged GM crank -Forged arp 7/16 bolt rods -JE pistons -Ported Iron heads -GM 4 bolt heavy duty block -Comp cams custom grind cam with stud girdle, roller rockers ect. -B&M megablower 420 (based on research a good blower that falls between a 6-71 and 8-71 size, based on B&M's own design that has supported up to 1000hp depending on the engine used) -Air/water aftercooler -Demon carbs jetted and tuned on the dyno -8.5:1 compression setup for 93 octane Dynoed 705 hp (very mild for pumpgas can easily support more) Good reliable engine that just has dyno time after being refreshened. $8500 complete ready to run. Call with any more specifics, we changed over to cars and turbo smallblocks so we are selling the boat parts. I can also get you into contact with the engine builder as well for any more questions. Thanks! Sam D. 423 605 2083 The engine is located in Chattanooga TN. |
[IMG]http://i57.tinypic.com/ff7sqv.jpg[/IMG]
|
[IMG]http://i58.tinypic.com/2jaz49v.jpg[/IMG]
|
Originally Posted by DRInnovations
(Post 4228952)
Here is a Complete engine, fresh rebuild still on the Dyno cart.
The engine was built buy Garry Grimes twister engines out of Atlanta Ga (he builds MANY successful offshore engines) It is a 502 big block chevy Intake to oilpan, with distributer and fuel pump. -Forged GM crank -Forged arp 7/16 bolt rods -JE pistons -Ported Iron heads -GM 4 bolt heavy duty block -Comp cams custom grind cam with stud girdle, roller rockers ect. -Edelbrock 10-71 megablower -Air/water aftercooler -Demon carbs jetted and tuned on the dyno -8.5:1 compression setup for 93 octane Dynoed 705 hp Good reliable engine that just has dyno time after being refreshened. $8500 complete ready to run. Call with any more specifics, we changed over to cars and turbo smallblocks so we are selling the boat parts. I can also get you into contact with the engine builder as well for any more questions. Thanks! Sam D. 423 605 2083 The engine is located in Chattanooga TN. |
I would like to sell complete. I have it priced for a pretty good deal for someone. We are trying to work with grimes on the 4v mercury Lsx heads on a hotrod setup so hopefully this puts a small dent in that project hahaha.
feel free to text or email as well [email protected] |
That is a b&m 420 mega blower. It's a little smaller than an 8-71, little bigger than a 6-71.
|
I would be a little concerned with the parts and knowledge of the engine with a description of a B&M 420 as a edelbrock 10-71 ( which doesn't even exist)
|
502's with a mechanical fuel pumps hanging off the side sure are hard to come by in these parts .that would make a great motor for a shovelnose hydro ,or my sj
|
Originally Posted by airjunky
(Post 4229174)
502's with a mechanical fuel pumps hanging off the side sure are hard to come by in these parts .that would make a great motor for a shovelnose hydro ,or my sj
|
Bump for the bowtie ..
|
All times are GMT -5. The time now is 10:33 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.