Fresh 502 MPI's w/ Lots of Upgrades
#1
Registered
Thread Starter
Join Date: Nov 2014
Location: Winchester, TN
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
Fresh 502 MPI's w/ Lots of Upgrades
Gen 6 502 MPI's
Currently in my 2000 Fountain 32 Fever
Less than 10 Hours Since Rebuilds
Bored 60 Over
All new bearings and seals
Reworked Merlin Heads with New Springs
JE Pistons
Eagle Rods
Comp Cams
New Comp Lifters
Crane Gold Rockers
New Timing Chains
Balanced Rotating Assembly
New Oil Pumps
New Oil Pans
Converted to MEFI 4
ECM Custom Tuned by Arizona Speed and Marine
Injectors Cleaned and Flow Tested
New Starters
New Alternators
New Waters Pumps
New Sparks Plugs
New Plugs Wires
Stainless Marine Headers
Bellhousing & Couples Included
Both painted Merc Racing Blue
Engines Sounds and Runs Great
$20,000 for Both
Located in TN
Currently in my 2000 Fountain 32 Fever
Less than 10 Hours Since Rebuilds
Bored 60 Over
All new bearings and seals
Reworked Merlin Heads with New Springs
JE Pistons
Eagle Rods
Comp Cams
New Comp Lifters
Crane Gold Rockers
New Timing Chains
Balanced Rotating Assembly
New Oil Pumps
New Oil Pans
Converted to MEFI 4
ECM Custom Tuned by Arizona Speed and Marine
Injectors Cleaned and Flow Tested
New Starters
New Alternators
New Waters Pumps
New Sparks Plugs
New Plugs Wires
Stainless Marine Headers
Bellhousing & Couples Included
Both painted Merc Racing Blue
Engines Sounds and Runs Great
$20,000 for Both
Located in TN
Last edited by rudybilt; 08-21-2016 at 11:51 PM.
#5
Registered
Thread Starter
Join Date: Nov 2014
Location: Winchester, TN
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
Good questions but unfortunately I was so eager the boat in the water I did have time dyno.
I can conservativly say 500+ hp.
I am willing to set up dyno time for any serious buyer.
I can conservativly say 500+ hp.
I am willing to set up dyno time for any serious buyer.
#7
Registered
Thread Starter
Join Date: Nov 2014
Location: Winchester, TN
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
They we built by a friend of mine that has been building boat engine and parts for 25+ years. They were in my 32 Fountain. I have only ran them up to 4500 rpm at close to 80.
#9
Registered
Thread Starter
Join Date: Nov 2014
Location: Winchester, TN
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
Absolutely
I had the starboard melt a bearing last summer due to operator error. I ran a low weight synthetic oil during break-in and did not keep close enough attention to the oil level and pressure. Expensive mistake.
Starboard engine got all new parts over the winter. I have had the boat out several times this summer and hope to make the Lake Cumberland Poker Run in two weeks.
I had the starboard melt a bearing last summer due to operator error. I ran a low weight synthetic oil during break-in and did not keep close enough attention to the oil level and pressure. Expensive mistake.
Starboard engine got all new parts over the winter. I have had the boat out several times this summer and hope to make the Lake Cumberland Poker Run in two weeks.