Parting out tripple engine SSM boat tons parts
#13
Registered
Join Date: Apr 2013
Location: Lake Winnebago
Posts: 203
Likes: 0
Received 0 Likes
on
0 Posts
Do those engine oil filter heads have a thermostat? What is the WIX filter number on those filters?....I cant make it out in the pictures.
Id be interested in 2 if you are willing to separate them from the engines.
Id be interested in 2 if you are willing to separate them from the engines.
#16
Gold Member
Gold Member
Thread Starter
iTrader: (5)
Join Date: Oct 2005
Location: Olmsted Falls,Ohio Marblehead,Oh
Posts: 11,634
Likes: 0
Received 204 Likes
on
132 Posts
I have one left, 572 CI tall deck here, was winterized and stored for 6 or so years and I fired them up with zero issues, could only run on hose on floor.
Cobra power did heads in 2011 I was told by past owner nephew (owner passed away)
What I do know
572CI built by hawk think refreshed in 2011 also but not sure, probably has Callie’s crank and Oliver rods that’s what they used back then.
Merlin 345 cc heads
Fully ported with head studs
Roller cam
Tie bar roller lifters
Crane 1.7 rockers
Weiand team G intakes with tall deck adaptors
1050 dominator
No headers no bell housing or trans, no engine mounts the rest will be as seen. Drop in and go!
This engine runs, ran great you can toss in and go, or refresh because it sat there is no warranty of any kind sold as is. Always fresh water since 1989 for sure boat was 1987.
8500.00 picked up 44138 Ohio
Cobra power did heads in 2011 I was told by past owner nephew (owner passed away)
What I do know
572CI built by hawk think refreshed in 2011 also but not sure, probably has Callie’s crank and Oliver rods that’s what they used back then.
Merlin 345 cc heads
Fully ported with head studs
Roller cam
Tie bar roller lifters
Crane 1.7 rockers
Weiand team G intakes with tall deck adaptors
1050 dominator
No headers no bell housing or trans, no engine mounts the rest will be as seen. Drop in and go!
This engine runs, ran great you can toss in and go, or refresh because it sat there is no warranty of any kind sold as is. Always fresh water since 1989 for sure boat was 1987.
8500.00 picked up 44138 Ohio
#18
Registered
Join Date: Oct 2004
Location: clarksburg nj
Posts: 245
Likes: 0
Received 0 Likes
on
0 Posts
ssm4
Parting out nitro, all parts always fresh water Great Lakes, very good condition and always maintained with open checkbook until owner passed it sat, all parts appear to be in great working condition. If you see something needed ask for price.
Offers accepted within reason, pm me, if you have nothing good to say save it, I don’t have time for BS. I average my prices off what i see things selling for, I do my research before listing.
Prefer Pick up only on huge parts 44138 Ohio
Will ship smaller items and possible big items if you help arrange freight but rather guys come see what they are buying in person
I have a full SSM4 conversion here
Boat has been sitting but everything spins nice and feels great, transmissions worked when parked a few years ago so should now, I see no reason why not.
****engines are 572’s working on firing them and parts list before I price them.... I do know tall decks, Merlin 345 heads, roller cams look to be nice lift, crane rockers, weiand team G intakes with tall deck adaptors and dominators PRICES TO BE DETERMINED on engines ASAP.
You get
2 SSM4 small shaft drives 19 spline
2- transom assemblies with trim cylinders and lines to cylinders
2- Extension boxes
2- carrier bearings and driveshafts
2- 72c transmissions with driveline style tailstocks
All parts from transmissions back to prop shaft that you need
Came from Tripple engine boat so no tie bar or steering plates, I do have a tie bar and plates separate for another 1000.00 from ssmiii parts I have here
18,000.00 picked up 44138 Ohio Or take off 2500.00 less 2 transmissions
Single SSMIII RH drive (1.5 ration I believe) 2500.00
Single trans with driveline tailstock 1250.00
Single extension box with carrier and driveshaft 3500.00
Single SSM humble no trim cylinders 1500.00
SSM trim cylinders 400.00
Hydraulic steering system helm to drives 2500.00
Stelling greens 2500.00 a set great shape, add 1000.00 for Y pipes (have 3 sets)
Non cooler bell housings 100.00 each
HD damper plates 150.00 each.
Coolant crossovers 200.00 set with stat housings
Tons of small parts here just ask me...
Parting entire boat so lots of parts to be listed
Offers accepted within reason, pm me, if you have nothing good to say save it, I don’t have time for BS. I average my prices off what i see things selling for, I do my research before listing.
Prefer Pick up only on huge parts 44138 Ohio
Will ship smaller items and possible big items if you help arrange freight but rather guys come see what they are buying in person
I have a full SSM4 conversion here
Boat has been sitting but everything spins nice and feels great, transmissions worked when parked a few years ago so should now, I see no reason why not.
****engines are 572’s working on firing them and parts list before I price them.... I do know tall decks, Merlin 345 heads, roller cams look to be nice lift, crane rockers, weiand team G intakes with tall deck adaptors and dominators PRICES TO BE DETERMINED on engines ASAP.
You get
2 SSM4 small shaft drives 19 spline
2- transom assemblies with trim cylinders and lines to cylinders
2- Extension boxes
2- carrier bearings and driveshafts
2- 72c transmissions with driveline style tailstocks
All parts from transmissions back to prop shaft that you need
Came from Tripple engine boat so no tie bar or steering plates, I do have a tie bar and plates separate for another 1000.00 from ssmiii parts I have here
18,000.00 picked up 44138 Ohio Or take off 2500.00 less 2 transmissions
Single SSMIII RH drive (1.5 ration I believe) 2500.00
Single trans with driveline tailstock 1250.00
Single extension box with carrier and driveshaft 3500.00
Single SSM humble no trim cylinders 1500.00
SSM trim cylinders 400.00
Hydraulic steering system helm to drives 2500.00
Stelling greens 2500.00 a set great shape, add 1000.00 for Y pipes (have 3 sets)
Non cooler bell housings 100.00 each
HD damper plates 150.00 each.
Coolant crossovers 200.00 set with stat housings
Tons of small parts here just ask me...
Parting entire boat so lots of parts to be listed