Go Back  Offshoreonly.com > Offshoreonly Marketplace > Swap Shop
Eickert 1000 hp Long Blocks >

Eickert 1000 hp Long Blocks

Eickert 1000 hp Long Blocks

Old 11-12-2019, 09:23 PM
  #1  
Platinum Member
Platinum Member
Thread Starter
iTrader: (4)
 
endeavour32's Avatar
 
Join Date: May 2009
Location: Chicago, IL; Onekama, MI
Posts: 3,741
Received 26 Likes on 10 Posts
Default Eickert 1000 hp Long Blocks

These are Keith Eickert 1000 long blocks. The blowers, ECU's and ignition are sold and long gone. Everything else is included. These have 160 original hours on them I had one lifter fail, and it did scuff the lifter bore in one bore. The engine has been partially dissembled and inspected, and all the other parts are fine. That engine needs to be rebuilt.

The other engine has had the heads removed but is otherwise still assembled.

Both heads have been fully rebuilt, and ported by Jim Valako. These are ready to bolt on.

I have new Bullet cams that are included. With the proper supercharger these engines should produce between 1200-1350 hp, With the cams provided, 250 hours of run time between rebuilds. When I chose these cams, I was very specific I wanted a very reliable valvetrain.

Here are the specs on the engines:

Block: Dart Big M- steel caps
Crank: Callies Magnum 4.375
Rods: Carrillo PRO H Beam
Pistons: CP Forged Dish 4.554
Cam: Bullet Custom Cam- NEW
Heads: Canfield 350- Rebuilt and Ported buy Jim Valeko. Zero hours!
Rockers: TD Shaft.
Lifters- Morel Ultimate Solid .904 lifters (one set NEW, you will need to buy the other set)

Plus full Keith Eickert accessories:
2 Piece Valve Covers
14 quart external oil pump pan
Crossovers
Ignition bracket
3 Stage water pumps
Remote Oil Filer housing

Additional Accesories:
Steel Flywheels
Duel Cooler Bellhousings with Coolers
HD Drive Plates
Peterson external oil pumps
FluidDampers
Alternators
All Brackerts

If you are looking to build some big power engines, this a a great chance to save a lot of money over new. Again, these need to be rebuilt. If I were going to run these I would replace all the bearings, fresh hone, and replace the rings. You don't need to do this, but that is what I would do! You are looking at close to $50k in parts if purchased new. These are all top shelf parts and not cheap Chinese parts with a brand name stamped on them. Do your research and you will see I'm very close in my parts pricing.

I would like to get $16,000 for everything, yes that's both engines. I'm open to offers, but I really feel the price is a deal considering what you are getting.

Rebuild these yourself if you are capable, and save even more, or have the engine builder of your choice rebuild them. Heads are done, so only the short block needs to be freshened up.



endeavour32 is offline  
Old 11-15-2019, 08:48 PM
  #2  
Platinum Member
Platinum Member
Thread Starter
iTrader: (4)
 
endeavour32's Avatar
 
Join Date: May 2009
Location: Chicago, IL; Onekama, MI
Posts: 3,741
Received 26 Likes on 10 Posts
Default

I'm also offering these without the new cams and set of lifters for $14500.
endeavour32 is offline  
Old 02-02-2020, 06:17 PM
  #3  
Platinum Member
Platinum Member
Thread Starter
iTrader: (4)
 
endeavour32's Avatar
 
Join Date: May 2009
Location: Chicago, IL; Onekama, MI
Posts: 3,741
Received 26 Likes on 10 Posts
Default

Great deal on some top shelf engines! Valeko just finished the heads!
endeavour32 is offline  
Old 02-11-2020, 06:35 PM
  #4  
Platinum Member
Platinum Member
Thread Starter
iTrader: (4)
 
endeavour32's Avatar
 
Join Date: May 2009
Location: Chicago, IL; Onekama, MI
Posts: 3,741
Received 26 Likes on 10 Posts
Default

$15,000 for everything.

I have I have $5k in having the heads rebuilt & ported, new cams and set of lifters. This is a killer deal, someone has to need a great set of engines.
endeavour32 is offline  
Old 02-14-2020, 07:37 AM
  #5  
Platinum Member
Platinum Member
Thread Starter
iTrader: (4)
 
endeavour32's Avatar
 
Join Date: May 2009
Location: Chicago, IL; Onekama, MI
Posts: 3,741
Received 26 Likes on 10 Posts
Default

bump
endeavour32 is offline  
Old 03-14-2020, 06:50 PM
  #6  
Platinum Member
Platinum Member
Thread Starter
iTrader: (4)
 
endeavour32's Avatar
 
Join Date: May 2009
Location: Chicago, IL; Onekama, MI
Posts: 3,741
Received 26 Likes on 10 Posts
Default

Will separate
endeavour32 is offline  
Old 03-28-2020, 12:10 PM
  #7  
Platinum Member
Platinum Member
Thread Starter
iTrader: (4)
 
endeavour32's Avatar
 
Join Date: May 2009
Location: Chicago, IL; Onekama, MI
Posts: 3,741
Received 26 Likes on 10 Posts
Default

Bump
endeavour32 is offline  
Old 03-29-2020, 08:52 AM
  #8  
Platinum Member
Platinum Member
iTrader: (1)
 
KAAMA's Avatar
 
Join Date: Oct 2000
Location: Western Michigan
Posts: 4,349
Likes: 0
Received 0 Likes on 0 Posts
Default

What is the CID on these engines, Mike?
KAAMA is offline  
Old 03-29-2020, 09:09 AM
  #9  
Platinum Member
Platinum Member
Thread Starter
iTrader: (4)
 
endeavour32's Avatar
 
Join Date: May 2009
Location: Chicago, IL; Onekama, MI
Posts: 3,741
Received 26 Likes on 10 Posts
Default

Mark they are 572's
endeavour32 is offline  
Old 04-01-2020, 03:38 PM
  #10  
Platinum Member
Platinum Member
Thread Starter
iTrader: (4)
 
endeavour32's Avatar
 
Join Date: May 2009
Location: Chicago, IL; Onekama, MI
Posts: 3,741
Received 26 Likes on 10 Posts
Default

bump
endeavour32 is offline  

OSO Sponsor
OSO Advertiser
OSO Advertiser

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

OSO Advertiser