cleaning out the shop-xr bravo-exhaust-more
10-31-2021, 08:10 PM
#1
Registered
Thread Starter
Join Date: Jan 2007
Location: Murrayville Georgia
Posts: 1,816
Likes: 0
Received 891 Likes
on
319 Posts
cleaning out the shop-xr bravo-exhaust-more
helping my buddy clean out his shop and now the parts are cluttering up my floor.
set Gil manifolds, told they were on a display engine that Wellcraft boats used at shows. look to have never been run.
tailpipes for the above Gil manifolds, they look new but one has a dent in the side.
XR Bravo, top and bottom are separated and the lower gear set is broken, the upper turns good and seems fine but I have not pulled the rear cover to look inside.
15x20 three blade cleaver
set of stock cast iron BBC manifolds with stainless risers
three bellhousings
early sea pump with bronze rear in/out plate
chrome thermostat housing
lots more that I have not gotten to yet.
feel free to ask any questions
set Gil manifolds, told they were on a display engine that Wellcraft boats used at shows. look to have never been run.
tailpipes for the above Gil manifolds, they look new but one has a dent in the side.
XR Bravo, top and bottom are separated and the lower gear set is broken, the upper turns good and seems fine but I have not pulled the rear cover to look inside.
15x20 three blade cleaver
set of stock cast iron BBC manifolds with stainless risers
three bellhousings
early sea pump with bronze rear in/out plate
chrome thermostat housing
lots more that I have not gotten to yet.
feel free to ask any questions
VIP Member
11-01-2021, 06:14 PM
#3
Registered
Thread Starter
Join Date: Jan 2007
Location: Murrayville Georgia
Posts: 1,816
Likes: 0
Received 891 Likes
on
319 Posts
asking $2,000 for the manifolds with the diffuser plates and $800 for the tails or $2600 for both. was told they were never run and the inside is shiny and clean so I think that is right.
11-01-2021, 10:03 PM
#5
Registered
Thread Starter
Join Date: Jan 2007
Location: Murrayville Georgia
Posts: 1,816
Likes: 0
Received 891 Likes
on
319 Posts
parts are at the shop in Clermont GA. about an hour east of Atlanta.
asking $2k for the upper and $1k for the lower. will make a better deal on both together.
any one with questions can get me during the day on my cell at 954-279-2628 ( still have a fla cell)
thanks
steve
asking $2k for the upper and $1k for the lower. will make a better deal on both together.
any one with questions can get me during the day on my cell at 954-279-2628 ( still have a fla cell)
thanks
steve
11-02-2021, 01:09 PM
#6
How much for the cast iron front engine mounts to zip 32905 ? i don't need or want the pedestals but wanna see what else is in that plastic bin
11-02-2021, 04:37 PM
#7
Registered
Thread Starter
Join Date: Jan 2007
Location: Murrayville Georgia
Posts: 1,816
Likes: 0
Received 891 Likes
on
319 Posts
the pedestals are eddie marine or some such. they are solid billet ones so sure you dont want them? take $150 for the mounts and pedestals. will need to figure shipping but flat rate Post Office would probably not be much. I can separate them though if all you want is the engine side $40 plus shipping for them
11-02-2021, 06:02 PM
#8
I'll hold off, these would be for a project that isn't even on the back burner yet. I have stamped but heard the cast were stronger.
