Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: mopower
Showing results 1 to 22 of 22
Search took 0.01 seconds.
Forum: Formula
06-12-2006, 09:48 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

This last winter was the first time I winterized my new ones in three years. Past years they came out and spent the winter in the garage :(
Forum: Formula
06-12-2006, 05:17 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

I also tried (two weeks ago) a pair of borrowed labbed 24 Bravos :eek: . From 3000 to 5000 rpm it was a rocketship but my rpms were too high.I was hitting 6000 and not full throttle yet so I backed...
Forum: Formula
06-12-2006, 05:09 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

There is a small metal triangle bolted to the top of the Quadrajet linkage arm on the side of the carb. This extends the length of the arm and now requires more movement at the sticks.
Forum: Formula
05-02-2006, 09:45 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

Yep , Imco Powerflows
Forum: Formula
05-01-2006, 05:43 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

Very nice :cool:
I had to work on my exhaust to get to fit too :(
Forum: Formula
04-13-2006, 09:20 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

B1's.
Sounds like you've been pretty busy with yours too :drink:
Forum: Formula
04-13-2006, 04:47 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

Not off hand but I did replace mine 2 years ago. All I did was call Formulas tech line with my HIN # and they told me exactly what I needed. Talk about service after the sale...how about 17 years...
Forum: Formula
10-04-2005, 09:36 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

Close...real close
Forum: Formula
10-04-2005, 07:28 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

Well , the tilt limit also varies if the drives are straight(greatest tilt) or if they are turned slightly(the least tilt room available)
Here's some pics from another 272 hyd.steering install
Forum: Formula
10-03-2005, 05:21 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

Most I've seen are 454s. There is one with 350s at the marina where I launch. I think you would be hard pressed to get 60 mph out of 350s , but a lot more room in the engine comp. to work on them. I...
Forum: Formula
10-02-2005, 08:57 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

You won't be able to tilt all the way up as center mounted steering rams will hit the center pod of the ST. I have K-planes and no room to mount the rams outside the drives. A friend of mine has...
Forum: Formula
10-02-2005, 08:15 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

I have XS Marine steering. And No , it's not installed yet. I farted around from May to the week before Labor day with some type of slippage problem. Right engine would spim 5900 rpm and at 3000 on...
Forum: Formula
08-22-2005, 07:05 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

525 per side , I would think upper 70 to near 80. Non stepped hulls tend to be a little slower but you probably already know this.
28 Bravos should work with 1.5 gears. No real need for expense of...
Forum: Formula
05-09-2005, 08:36 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

540s can be standard or tall deck. Mine are standard , as the tall deck is also slightly wider since the 90* V goes out as welll as up with the increased deck height. Believe me when I say "One more...
Forum: Formula
05-08-2005, 09:12 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

Mine are Weiand Team G intakes. The carb surface is 4 1/2 inches above the mounting holes on the head. I'm running Dominators and Eddie Marine 5x10 arrestors , which gives me about an inch over the...
Forum: Formula
02-17-2005, 08:53 AM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

The sticks. New illuminated rocker switches :cool:
Forum: Formula
02-17-2005, 08:51 AM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

Lets see what I can do :D . Here's the pass side and the rear of instruments with the new prewired. All the existing wiring plugged into the new guages.
Forum: Formula
02-16-2005, 09:05 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

Thanks.

Bottom row is same as factory. Middle row has water pressure on the ends. . Top row is fuel pres. and oil temp.
Gotta keep a watch on the ponies :D . Also if you look close at the engines...
Forum: Formula
02-16-2005, 11:12 AM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

Imco Powerflows with stainless elbows and also stainless pipe to the stern. The outside pipes angle inward and the rubber hoses melted where the exhaust was blowing against it. With the stainless and...
Forum: Formula
02-15-2005, 08:56 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

And this is how to wrap it up for the winter :(
Forum: Formula
02-15-2005, 08:54 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

I could probably do a complete 272 thread myself(all except the ST platform...haven't messed with that...yet)
Forum: Formula
02-15-2005, 08:39 PM
Replies: 67
Views: 11,535
Posted By mopower

Re: The complete 272 thread

Right Masi, my engines spend so much time hanging in the air they think they're airplane engines :D

Mine did have 330s but here's my 625/540s. . Trust me when I say you need good hydraulic...
Showing results 1 to 22 of 22


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.