Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: SB
Showing results 1 to 15 of 15
Search took 0.00 seconds.
Forum: General Q & A
02-26-2014, 01:43 PM
Replies: 81
Views: 25,811
Posted By SB

I don't get it. Looks like you ported the heads...

I don't get it. Looks like you ported the heads to a standard intake manifold - ie: one with intake to head bolts between each set of runners. Where these bolts are, but your heads don't have them,...
Forum: General Q & A
02-26-2014, 01:34 PM
Replies: 81
Views: 25,811
Posted By SB

There's a few crossram bbc intake manifolds...

There's a few crossram bbc intake manifolds available out there. Just grab some TBI's and go.........to the nut house. LOL.
Forum: General Q & A
02-26-2014, 01:32 PM
Replies: 81
Views: 25,811
Posted By SB

I would like to say, you can further your project...

I would like to say, you can further your project and have the most usable horsepower, is actually using your engine.

Go have a few buds and get the damn thing done already.
Forum: General Q & A
02-26-2014, 12:46 PM
Replies: 81
Views: 25,811
Posted By SB

Yes, i'll clarify. Waste of time. You...

Yes, i'll clarify.

Waste of time.

You are overthinking.....Unless, you know how to properly shape the plenum and esoecially runner entrances, compute port lengths and properly adjust them, and...
Forum: General Q & A
02-26-2014, 11:15 AM
Replies: 81
Views: 25,811
Posted By SB

If the intakes port entrances are smaller than...

If the intakes port entrances are smaller than the heads , then don't touch'm.

Put the intake on and look down the runners to see. When you get all ports to line up with slightly shifting intake...
Forum: General Q & A
02-25-2014, 08:13 PM
Replies: 81
Views: 25,811
Posted By SB

So...I've been gone for a few hrs. Enough time to...

So...I've been gone for a few hrs. Enough time to have that Dart oval installed. Is it on yet ?
Forum: General Q & A
02-25-2014, 08:12 PM
Replies: 81
Views: 25,811
Posted By SB

Shhhh. Those are from Dart. Keep it a secret. LOL.

Shhhh. Those are from Dart. Keep it a secret. LOL.
Forum: General Q & A
02-25-2014, 04:09 PM
Replies: 81
Views: 25,811
Posted By SB

A big one with 'lower end' rpm with dual planes...

A big one with 'lower end' rpm with dual planes is that you don't have as much cylinder to cylinder (via firing order) intake air/fuel charge robbing, especially at low speeds.

The bigger the air...
Forum: General Q & A
02-25-2014, 03:51 PM
Replies: 81
Views: 25,811
Posted By SB

I did not read all responses since I posted last,...

I did not read all responses since I posted last, so sorry if someone posted this.

Nope. It's math. No matter what engine is measured, they'll cross right there. Torque is measured. HP is equated...
Forum: General Q & A
02-25-2014, 03:03 PM
Replies: 81
Views: 25,811
Posted By SB

Sure. Here you go. ...

Sure. Here you go.

http://trailerparkboys.org/forums/Smileys/default/passone.gif
Forum: General Q & A
02-25-2014, 02:54 PM
Replies: 81
Views: 25,811
Posted By SB

I was continuing on with what you said. Round...

I was continuing on with what you said. Round table discussion, if you will.:cool-smiley-011:
Forum: General Q & A
02-25-2014, 02:15 PM
Replies: 81
Views: 25,811
Posted By SB

Almost all engines will produce peak hp...

Almost all engines will produce peak hp 1200-1400rpm over peak torque. That's just how it works, unless someone f*ked up something.

Usually propping for around 200-300rpm under peak hp in normal...
Forum: General Q & A
02-25-2014, 12:57 PM
Replies: 81
Views: 25,811
Posted By SB

I did 502 with same sort of cam, decent afmkt...

I did 502 with same sort of cam, decent afmkt heads, on the dyno with full wet exhaust. Different intakes, with/without this and that accessory, and etc,etc

On water with different motors as far...
Forum: General Q & A
02-25-2014, 11:44 AM
Replies: 81
Views: 25,811
Posted By SB

You guys are thinking too much.

You guys are thinking too much.
Forum: General Q & A
02-25-2014, 10:48 AM
Replies: 81
Views: 25,811
Posted By SB

This is an actually easy thread to answer. ...

This is an actually easy thread to answer.

Your motor is big enough, and your heads a good enough, where even with a 'smaller cam' and lower operating rpm then say a street strip car , that it...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.