Offshoreonly.com - Cig 20 on Craigslist

Page 3 of 4

Show 40 post(s) from this thread on one page

Offshoreonly.com (https://www.offshoreonly.com/forums/)

- Cigarette (https://www.offshoreonly.com/forums/cigarette-32/)

- - Cig 20 on Craigslist (https://www.offshoreonly.com/forums/cigarette/271602-cig-20-craigslist.html)

Pot of Gold

03-01-2012 09:13 AM

it sure would be a nice ride once it were finished.

O.C.Barry

03-01-2012 08:03 PM

Quote:

Originally Posted by Holy Smokes (Post 3630528)

I agree. It's legit. Several details of the deck and hull look exactly like my '74. Our hatches are different as I have what used to be the flat hatch, but someone along the way added a scoop. The fuel tank, the fuel sender access, the floorboard piece, the stringers, windscreen recess, mahogany stripe recess, etc. all scream "I'm for real!". As Hotboat mentioned on the forward storage hatch latches, mine are the same, hood pins.

Not sure what the huge hole behind the rear seat is for and the access hole on the port side is in a odd location.

I thought the same thing, I had the floorboard out of my old 20 to upgrade the fuel lines and it looked exactly the same. It looks like someone added the rear access hole. Maybe the owner was a proctologist?

I still don't think the raised part of the hatch is factory. Mine had teak round hole bezels in the front of the hatch.

J-Bonz

03-02-2012 06:49 PM

Here's another one....

http://annapolis.craigslist.org/boa/2877576849.html

Cig19

03-05-2012 08:04 PM

Quote:

Originally Posted by Hotboat1 (Post 3630379)

I have a lot of concerns about this one. Without verifying the VIN it could be a splash. The engine hatch does not look right. It states that it is a 1980 but it has pre '75 vents on the side. The mldg looks to be alum and is flat??? Also, an '80 with a Volvo drive???? What is the deal with the markings where the pedestals were---- An octagonal one on the drivers side and a round one on the passenger side? It has race car hood pins instead of the twist in latches from the Donzi/Cigarette era. Am I wrong here?

I would agree and say probably a 73-75 hull. Mine had the old style hood pins and side vents as well. The Volvo was only used in the very first years with the the 350 small block. The raised hatch looks homemade ? Mine is one of the few I've seen not raised, no extra clearance needed for the small block.

Great project, wouldn't take much to complete and keep same power/drive setup. 60 mph is great for this size boat.

Cig19

03-05-2012 08:12 PM

4 Attachment(s)

Some pics of mine.

Biggus

03-06-2012 04:40 AM

Quote:

Originally Posted by Cig19 (Post 3634109)

Some pics of mine.

Very nice! Something cool about finding an old classic buried deep in a storage building. I need one of these!

Kurt

RebarBox

03-06-2012 11:04 AM

Quote:

Originally Posted by Cig19 (Post 3634109)

Some pics of mine.

WOW!! Very sharp boat.

Nothing better than seeing a clean, classic black boat with a Cig logo on the side.

Cig19

03-06-2012 12:07 PM

Thanks. This was a good time restoring and am ready to move on.

Winter is almost over and I will putting it up for sale. Comes with custom black tandem trailer with electric brakes. Never in salt water-always on lift on the Lake.

30K takes it home.:drool1:

Ken

Deuceman

05-12-2012 01:26 PM

Quote:

Originally Posted by Cig19 (Post 3634559)

Still for sale?
Hawkan

Glassic R.T.

05-12-2012 01:58 PM

Quote:

Originally Posted by Deuceman (Post 3685937)

Still for sale?
Hawkan

http:http://www.donzi.net/forums/showthre...e-19-ft-hull-1 and if you go to www.donzi.net there also is a 1975 20 Cig , TRS, Trailer , for $25K .

All times are GMT -5. The time now is 07:50 AM.

Page 3 of 4

Show 40 post(s) from this thread on one page