Nauti by Nature Cigarette 38 Top Gun Refresh!!
02-11-2013 | 07:57 PM
#41
VIP Member
Joined: Dec 2001
Posts: 10,398
Likes: 404
From: Cape Coral, Florida
Well... I bought a newer style (2004) backseat and put it in the boat and then took the boat to FLA to get the hatch (which was rotted) and new side panels made. That turned into re-doing everything. Gotta love these *&#$ing boats!!! 
__________________
Happily retired and living in Heavens waiting room.
Happily retired and living in Heavens waiting room.
02-12-2013 | 06:55 AM
#44
VIP Member
Joined: Jul 2003
Posts: 4,288
Likes: 779
From: Tulsa, GLOC
Tell me about it!
Pulled motors to install SCXs-
Now all new interior, several things in engine compartment geting fixed, new gimbals and helmets for drives, doing springs and lifters in motors, redynoing for smaller pullies!!
Hoping that we dont need chillers-- then redo hatchfor scoops
Gotta be Crazy cause IT never ends boys!!!
02-12-2013 | 09:35 AM
#45
Thread Starter
Registered
Joined: Jun 2011
Posts: 863
Likes: 0
Mark
02-27-2013 | 08:16 PM
#46
Thread Starter
Registered
Joined: Jun 2011
Posts: 863
Likes: 0
Parts are starting to show up from Bob Madara from Marine Kinetics!! http://www.marinekineticsonline.com
Bob Spec'd all the valve train parts!! The Custom Cams should be in next week
All the valve train components from Bob!
Isky 9000 Series Valve Springs
Morel 4603 Hyd Roller Lifters - (Cam Motion)
Pac Racing 10 Degree Light Weight Chromoly Retainers
Pac Racing 10 Degree Chromoly Locks & Comp Cams Valve Seals!
Bob Spec'd all the valve train parts!! The Custom Cams should be in next week
All the valve train components from Bob!
Isky 9000 Series Valve Springs
Morel 4603 Hyd Roller Lifters - (Cam Motion)
Pac Racing 10 Degree Light Weight Chromoly Retainers
Pac Racing 10 Degree Chromoly Locks & Comp Cams Valve Seals!
03-02-2013 | 11:45 PM
#47
Thread Starter
Registered
Joined: Jun 2011
Posts: 863
Likes: 0
Few pics from tonights session!
Blowers apart clean and ready for new bearings & Seals
New Bearings/Seals and Teflon Strips. (Before you get gung ho about replacing your strips you have to have a way to turn the teflon down to get .005" clearance from the rotor to the case)
New Gaskets
Blowers apart clean and ready for new bearings & Seals
New Bearings/Seals and Teflon Strips. (Before you get gung ho about replacing your strips you have to have a way to turn the teflon down to get .005" clearance from the rotor to the case)
New Gaskets
03-02-2013 | 11:56 PM
#49
Thread Starter
Registered
Joined: Jun 2011
Posts: 863
Likes: 0
Rebuilt the Snout with new bearings and seals!
New Blower Bearings & Seals installed.
Rotors installed
Bearings Retainers
Pay attention to this shim and what rotor it is on. This shim fine tunes the rotor timing and is VERY IMPORTANT!!
New ARP Pro Blower Gear Bolts!! Look for the timing marks on the gears, you can see the rotor timing here.
New Coupler installed
New Blower Bearings & Seals installed.
Rotors installed
Bearings Retainers
Pay attention to this shim and what rotor it is on. This shim fine tunes the rotor timing and is VERY IMPORTANT!!
New ARP Pro Blower Gear Bolts!! Look for the timing marks on the gears, you can see the rotor timing here.
New Coupler installed
polishing them back up....
