6 blade Herring prop nut removal
 

Finally got #6SSM dry sumps and am looking for 6 blade prop nut removal advice. Also,should I put it in gear or out of gear? Thanks Guys.

1 7/16 inch socket. Not sure of your transmissions, but you dont want to shift without motor running, so out of gear is how I do it. Use a block of wood, or their are a variety of tools made to hold the prop to loosen nut.

The block of wood always works, but especially with thin/sharp labbed blades and Herrings, I get nervous about damaging a blade, especially when you do the side that requires pressure on the leading edge.

For this case, I recommend cutting your own block of wood with a wedge shape to it that will distribute the pressure to two blades, vs. one.

The prop bite wrenches on the market work, but I have seen them slip off as well. I guess you have to hold your tongue in the right spot.

I use a cordless impact ....:cool-smiley-011:

Get you a Dewalt impact gun. No need for prop stops then. Works great and very easy. Leave tranny in nuetral

Putting the transmission in gear with a BW72C does exactly nothing when not running, as they require hydraulic pressure to engage the clutches.

I wouldn't worry about hurting the props with a block of wood. Just keep yourself from getting cut up.

Thanks Guys,The block of wood is scary as Brett of BB blades says he gets a lot of repairs from guys that use wood blocks. I like the impact gun idea .The 6 blade herrings are tough to get the wood near the hub where the strength is. Brett recommends a friend with thick leather gloves hold the prop while you wrench the nut. You guys are great! Thanks for your suggestions ,it is really appreciated.

I wonder why, after all these years of making these things, no one has built a propshaft with a hex at the end, slightly smaller than the thread diameter, so you can get another wrench against it. Or, maybe a huge ( like 3/4" or 7/8") hex key and do it like a rocker stud?

I can promise you, once you use an impact gun. You will never be without them, plus they are nice to have in case of trailer flats.
I don't see how you could ever get enough torque with someone holding just the prop.

A big cordless impact is the way to go. Couldn't live without that tool anymore. Stick with a Dewalt or Makita. Some of the other off brand stuff hasn't been the greatest, and some of the craftsman impacts I have seen haven't impressed me either.

Also, make sure you do not use any reducers/adapters on your impact as that lessens torque. Get a socket that fits right onto your impact. McMaster Carr has a nice impact rated socket that was priced well and works great.

Keep in mind to that most cordless impacts only produce about 1/3 of the torque that they are rated for (maybe a little more if the battery is plump full) whether it be dewalt or makita. You should get one "rated" for 300ft.lbs of "max torque". Some of them have ratings for working torque as well.....

Anyone have a recommendation on which cordless impact gun? I looked online and there's too many of them!! :D

What model have you all had good experience with?

1/2" drive I assume?

Thanks in advance,
Craig

I like my DeWALT DC800KL. But I've never owned anything else, so not much of a comparison.

EDIT: One thing about the DeWALT to have in mind is, if you take it places and use it somewhat much, you should get extra batteries so you have 3. It's kinda power hungry.

I've got a Matco 3/8. I was never overly excited about it's performance, but the price was right. (Gift from OSO member!)

I'll probably reinvest in a 1/2 from Snap-On, Matco, or DeWalt one day soon.

i use an impact tool to remove the prop, but not to torque it on install. i am not confident of the unkown torque of the imapct tool. so i end up using the wood method or holding the prop by hand.

I've watched Bob Teague use a large rubber mallet to tighten the props on Miss Amsoil. I'm keeping a rubber mallet in the boat from now on, it's the easiest thing I've seen.

This is what we have, have tried several others and they are not up to the task of taking the nut off. As said the batteries dont last real long, but it comes with two. Plenty enough for a week end, plus its strong enough to remove lug nuts from your trailer, or car unless you put them on with a breaker bar.

This