Rotary Engines
09-07-2006 | 03:32 AM
#11
Registered
Joined: Sep 2006
Posts: 1,442
Likes: 0
From: Closer than you might think..........
Re: Rotary Engines
I have an Atkins built rotary in my autocross RX7. Three years and 32k miles running consistantly at 9500 RPM, no problems ever, runs like a champ. Atkins can build a rotary that is reliable and turns over some serious power. Hope this helps....Donnie
09-07-2006 | 08:07 AM
#12
Frank's Marine Service
Joined: Sep 2002
Posts: 11,959
Likes: 142
From: Elkton, MD
Re: Rotary Engines
Originally Posted by Fanatic
Check out the video...
http://www.xtremerotaries.com/main2/.../60-102mph.wmv
- Hull - Kevlar 1850 bullet, Bravo 1 XR leg
- Engine – X-Treme Rotaries 1962cc 20B (3 rotor) rotary engine, bridge ported, turbocharged, fuel injected
- Horsepower – 800hp 9500rpm 615 ft/lbs torque
- Speed – max 142 mph 9650rpm
- Tuning – by Anthony Rodrigues, Maztech of Melbourne
- Turbo – Garret GT42 1000hp
- Intercooler – PWR barrel water to air
It's been outlawed on the racing circuit because it was just kicking everybodies azz.
http://www.xtremerotaries.com/main2/.../60-102mph.wmv
- Hull - Kevlar 1850 bullet, Bravo 1 XR leg
- Engine – X-Treme Rotaries 1962cc 20B (3 rotor) rotary engine, bridge ported, turbocharged, fuel injected
- Horsepower – 800hp 9500rpm 615 ft/lbs torque
- Speed – max 142 mph 9650rpm
- Tuning – by Anthony Rodrigues, Maztech of Melbourne
- Turbo – Garret GT42 1000hp
- Intercooler – PWR barrel water to air
It's been outlawed on the racing circuit because it was just kicking everybodies azz.
09-07-2006 | 09:10 AM
#14
Thread Starter
Registered
Joined: Aug 2005
Posts: 8,779
Likes: 1
From: HOUSTON ,TX
Re: Rotary Engines
Originally Posted by marineclean
I have an Atkins built rotary in my autocross RX7. Three years and 32k miles running consistantly at 9500 RPM, no problems ever, runs like a champ. Atkins can build a rotary that is reliable and turns over some serious power. Hope this helps....Donnie
WHAT HP?
09-07-2006 | 10:55 AM
#17
Registered
Joined: Jun 2005
Posts: 1,232
Likes: 3
From: Chesapeake, Va.
Re: Rotary Engines
Originally Posted by marineclean
I have an Atkins built rotary in my autocross RX7. Three years and 32k miles running consistantly at 9500 RPM, no problems ever, runs like a champ. Atkins can build a rotary that is reliable and turns over some serious power. Hope this helps....Donnie
I recently built a ceramic seal motor which is capable of 800/900 hp and it's a two rotor 13b not a three rotor like the boat.
09-07-2006 | 11:00 AM
#18
Registered
Joined: Jun 2005
Posts: 1,232
Likes: 3
From: Chesapeake, Va.
Re: Rotary Engines
Originally Posted by METAL BROS RACING
no torque.
615 ft/lbs torque
615 ft/lbs is out of 120 cubic inches.
Here is a 13b (two rotor) dyno. Race engine running high boost...
Last edited by Fanatic; 08-09-2007 at 11:51 PM.
Thread
Thread Starter
Forum
Replies
Last Post
PhantomChaos
General Boating Discussion
24
10-10-2003 11:23 PM
