Offshoreonly.com - 28'-ish Single Engine Vee w/ true Surface Drive

Page 6 of 9

Show 40 post(s) from this thread on one page

Offshoreonly.com (https://www.offshoreonly.com/forums/)

- General Boating Discussion (https://www.offshoreonly.com/forums/general-boating-discussion-51/)

- - 28'-ish Single Engine Vee w/ true Surface Drive (https://www.offshoreonly.com/forums/general-boating-discussion/169454-28-ish-single-engine-vee-w-true-surface-drive.html)

tblrklakemo

09-27-2007 03:22 PM

Quote:

Originally Posted by Canada Jeff (Post 2287085)

What are Arneson trim plates?

see below l
\/

Jassman

09-27-2007 04:33 PM

Quote:

Originally Posted by Canada Jeff (Post 2287085)

What are Arneson trim plates?

http://www.arneson-industries.com/pa...ucts&id=rocker

new website-good reading

2112	09-27-2007 09:42 PM

Quote:

Originally Posted by Sydwayz (Post 2283764)

Again, no tabs installed because no one is sure what the boat will need, yet. It has not been run yet. It's getting 650HP.

Does that project belong to my old friend Jess Dodd? Very cool, looking forward to results.

How about pictures of the bilge!!

Rik	09-28-2007 01:09 AM

2 Attachment(s)

I forgot you like FORD! :D

Tom A.

09-28-2007 05:12 AM

2 Attachment(s)

George Desmond had an 18' Donzi w/ a stroked small block (600+hp) and an Arneson and that boat rocked! I know it ran well over 100 mph.

TeamSaris

09-28-2007 06:24 AM

Quote:

Originally Posted by Stormrider (Post 2286559)

Hustler ever do any single 26 ASDs?

I know of a twin small block one with them

2112	09-28-2007 11:51 AM

Quote:

Originally Posted by Rik (Post 2287759)

I forgot you like FORD! :D

Yep, we are a rare breed. Too bad so many people think you can't do with a Ford what you can do with a Chev. :rolleyes:

Tell Jess great job! :D:D

Stormrider

09-28-2007 02:06 PM

Quote:

Originally Posted by fast fun 2 (Post 2287806)

I know of a twin small block one with them

don't count. looking for single examples.
just curious cuz hustler uses them big time, y not on a 26 single?

Mike J

09-28-2007 03:03 PM

NO those on the web site are not the ones that were built into
the Scarab, They sent a insert to put into the mold on each
side on the bottom, Then the hull was molded complete so
that a pad was made just the right size to insert the trim plate
flush with bottom and even with the transom "Have I lost you
yet", Guess everything worked fairly well they won the first
race at the worlds in Key West that year. Mike J.

floatingphil

01-09-2008 10:48 AM

Quote:

Originally Posted by Sydwayz (Post 2282207)

This boat is/was an experiment; built for an guy who came to us wanting this specific setup. This is not a conversion. Dialing in is going to be a joint exercise. When the trailer was built, the boat had nothing on the transom; so the trailer is just temporary as is. The boat has not been in the water yet, so tab needs are undefined at this point.

It's something new and different for AT.
Who knows what's next?

Any updates on this?

All times are GMT -5. The time now is 12:14 PM.

Page 6 of 9

« First

Last »

Show 40 post(s) from this thread on one page