Notices
General Boating Discussion

IMCO SCX and SCT

Thread Tools
 
Old 05-02-2008 | 03:43 PM
  #1  
Thread Starter
VIP Member
 
Joined: May 2006
Posts: 35
Likes: 0
Default IMCO SCX and SCT

Does anyone have any new information or recent experience with either of these two drives?
milesd is offline  
Reply
Old 05-02-2008 | 04:07 PM
  #2  
Registered
 
Joined: Dec 2006
Posts: 202
Likes: 0
From: san diego
Default

Just put a twin set of SCX on the New Ultra 344sc and ran them this last weekend.
Bad Ass Industrial is offline  
Reply
Old 05-03-2008 | 05:00 PM
  #3  
Thread Starter
VIP Member
 
Joined: May 2006
Posts: 35
Likes: 0
Default

Thanks for your response.
I talked to John.
milesd is offline  
Reply
Old 05-03-2008 | 10:40 PM
  #4  
Registered
 
Joined: Jun 2006
Posts: 2,057
Likes: 0
Default

Originally Posted by Bad Ass Industrial
Just put a twin set of SCX on the New Ultra 344sc and ran them this last weekend.
And how'd they work out ? you guys like em? How do they compare to nxt's ?
stainless is offline  
Reply
Old 05-05-2008 | 07:33 PM
  #5  
Sonny Spectre 30's Avatar
Registered
 
Joined: Oct 2001
Posts: 490
Likes: 7
From: Raleigh, NC
Default

What motors? How'd they run compared to what you had before?
Sonny Spectre 30 is offline  
Reply
Old 05-05-2008 | 08:52 PM
  #6  
Registered
20 Year Member
 
Joined: Feb 2005
Posts: 1,920
Likes: 142
From: Atlanta
Default

I'd like to here more about the scx and the power in front of it.
tomcei is offline  
Reply
Old 05-05-2008 | 09:00 PM
  #7  
Registered
 
Joined: May 2005
Posts: 238
Likes: 0
From: Scottsdale
Default

Originally Posted by Sonny Spectre 30
What motors? How'd they run compared to what you had before?
710 Ilmors
Bottomfeeder is offline  
Reply
Old 05-06-2008 | 08:01 PM
  #8  
Sonny Spectre 30's Avatar
Registered
 
Joined: Oct 2001
Posts: 490
Likes: 7
From: Raleigh, NC
Default

I'm looking to put a set on my 2007 36' Spectre with 625 Ilmor's. Thinking about going up in drive height -2" and getting the big shaft (#6 props). Any suggestions based on your experience with these SCX drives?
Sonny Spectre 30 is offline  
Reply
Old 05-06-2008 | 08:12 PM
  #9  
Registered
 
Joined: May 2005
Posts: 238
Likes: 0
From: Scottsdale
Default

Originally Posted by Sonny Spectre 30
I'm looking to put a set on my 2007 36' Spectre with 625 Ilmor's. Thinking about going up in drive height -2" and getting the big shaft (#6 props). Any suggestions based on your experience with these SCX drives?
I believe they're still dialing in the 34,,no center pod and comparable beam and length to your Spectre,,,he should get you close
Bottomfeeder is offline  
Reply
Old 05-06-2008 | 09:15 PM
  #10  
Registered
 
Joined: May 2008
Posts: 11
Likes: 0
From: El Cajon, CA
Default

We're still doing our testing. We have only had the boat out one weekend so far and the conditions were less than ideal for testing. I will be doing a lot more testing this Thursday and Friday in California and then Saturday and Sunday in Havasu. I will let you know how everything goes next week. The boat is a 2009 Ultra 344 SC (34'4",10'4")with Ilmor 710s, IMCO SCX drives with standoff boxes, 1.34 gear ratio, 32 labbed Maximus props. So far I am very impressed with the IMCO SCX drives. This is the first boat built of this model, so I can't give you a comparison to any other engine and drive combos.
Johnny West is offline  
Reply


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.