Nothing to hide - Ilmor opens the door on my 725/Indy buildup
#91
AT Cult Member #3
![](https://www.offshoreonly.com/forums/images/icons/prop.gif)
![Default](/forums/images/icons/icon1.gif)
Thats right....you were pretty handy with that hammer....
and thanks for the help....you did spend some time with me to get it fixed...
Thanks again....and hope to see ya at some races this year...
Chuck...do you have any idea what she will run with that package..and what is the fastest a bat boat has run....
and thanks for the help....you did spend some time with me to get it fixed...
Thanks again....and hope to see ya at some races this year...
Chuck...do you have any idea what she will run with that package..and what is the fastest a bat boat has run....
Nice job Chuck. (As usual)
![Cool](/forums/images/smilies/cool.gif)
#92
Diamond Member #001
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
Thread Starter
iTrader: (2)
Join Date: Oct 2000
Location: Coastal North Carolina
Posts: 4,808
Likes: 0
Received 5 Likes
on
4 Posts
![Default](/forums/images/icons/icon1.gif)
![Lolhit](/forums/images/smilies/more/lolhit.gif)
It should be aound 100 mph. I've heard of a couple of 28's with blower engines running in the teens.
__________________
Retired! Boating full-time now.
Retired! Boating full-time now.
#93
Diamond Member #001
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
Thread Starter
iTrader: (2)
Join Date: Oct 2000
Location: Coastal North Carolina
Posts: 4,808
Likes: 0
Received 5 Likes
on
4 Posts
![Default](/forums/images/icons/icon1.gif)
These Ilmor guys continue to impress. The drive position sensor setup on the Indy is so simple, brilliant and compact that it took me a while to find it and figure it out. Once I did, they promptly helped me out in getting the same parts to read trim tab position as well. I was going to buy the Mercury SmartCraft trim tab sensors at roughly $800 for two tabs, but using Ilmor's setup will only set me back about $120, and is way, way simpler. No more cables!
__________________
Retired! Boating full-time now.
Retired! Boating full-time now.
#94
Registered
![Default](/forums/images/icons/icon1.gif)
These Ilmor guys continue to impress. The drive position sensor setup on the Indy is so simple, brilliant and compact that it took me a while to find it and figure it out. Once I did, they promptly helped me out in getting the same parts to read trim tab position as well. I was going to buy the Mercury SmartCraft trim tab sensors at roughly $800 for two tabs, but using Ilmor's setup will only set me back about $120, and is way, way simpler. No more cables!
#95
Diamond Member #001
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
Thread Starter
iTrader: (2)
Join Date: Oct 2000
Location: Coastal North Carolina
Posts: 4,808
Likes: 0
Received 5 Likes
on
4 Posts
![Default](/forums/images/icons/icon1.gif)
Started on the engine mounts today. That's a 3/4"-10 UNC bolt you see in the middle...
------------------------------------------
Finished them (except for powdercoat) this morning. Now I have to make spacers to compensate for the attachment points being higher up and farther forward..
------------------------------------------
Finished them (except for powdercoat) this morning. Now I have to make spacers to compensate for the attachment points being higher up and farther forward..
__________________
Retired! Boating full-time now.
Retired! Boating full-time now.
Last edited by C_Spray; 04-17-2010 at 10:39 AM.
#96
Diamond Member #001
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
Thread Starter
iTrader: (2)
Join Date: Oct 2000
Location: Coastal North Carolina
Posts: 4,808
Likes: 0
Received 5 Likes
on
4 Posts
![Default](/forums/images/icons/icon1.gif)
Got the old dash and wiring stripped out in preparation for the Ilmor stuff, the bilge painted, and the hatches bonded together this weekend. If you've never used Plexus before, be prepared with lots of ventilation. That stuff is intense, but it stuck two fiberglass parts together like they were made as one.
I'm beginning to see the light at the end of the tunnel now...
I'm beginning to see the light at the end of the tunnel now...
__________________
Retired! Boating full-time now.
Retired! Boating full-time now.
#97
VIP Member
![](https://www.offshoreonly.com/forums/images/icons/prop.gif)
![Default](/forums/images/icons/icon1.gif)
looks awesome chuck!
#98
Diamond Member #001
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
Thread Starter
iTrader: (2)
Join Date: Oct 2000
Location: Coastal North Carolina
Posts: 4,808
Likes: 0
Received 5 Likes
on
4 Posts
![Default](/forums/images/icons/icon1.gif)
Thanks, Rob. We're getting there. I wasn't so sure that we'd make the deadline for Smith Mountain Lake May 22, but R'Addiction was a huge help on Sunday. We're not giving up.
I salvaged part of the NACA ducts that we removed earlier to restore the hatch to a smooth profile. I will laminate these in for full strength, then cut the holes for the headers, and start making the blisters.
I salvaged part of the NACA ducts that we removed earlier to restore the hatch to a smooth profile. I will laminate these in for full strength, then cut the holes for the headers, and start making the blisters.
__________________
Retired! Boating full-time now.
Retired! Boating full-time now.