Offshoreonly.com
Page 9 of 10
« First
7
8
9
10
Show 40 post(s) from this thread on one page

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   General Boating Discussion (https://www.offshoreonly.com/forums/general-boating-discussion-51/)
-   -   Leak proof, 10 yrs warrantee headers. (https://www.offshoreonly.com/forums/general-boating-discussion/268562-leak-proof-10-yrs-warrantee-headers.html)

FIXX 02-11-2012 12:14 PM
fixx
 
1. a triple tube header?

2. inside primary tube with a coil that wraps around the inner tube then covered by a outter tube then exits the water out the tail?

3. a perfectly welded header a nitrogen tank to cool the header?

4. a perfectly sealed header with a on board a/c pump and water cooled condensor,then use the headers as a evaperator core which will cool the headers?

PARADOX 02-11-2012 12:35 PM
Originally Posted by mrfixxall (Post 3615121)
1. a triple tube header?

2. inside primary tube with a coil that wraps around the inner tube then covered by a outter tube then exits the water out the tail?

3. a perfectly welded header a nitrogen tank to cool the header?

4. a perfectly sealed header with a on board a/c pump and water cooled condensor,then use the headers as a evaperator core which will cool the headers?
YOu'r on the right track bud. :) :drink:

Dean Ferry 02-11-2012 12:41 PM
Originally Posted by rexone (Post 3614910)
Jason I remember your dad showing me those, had to be very early 90's at Miami Black Thunder booth I believe. A lot of folks poo poo'ed them back then. Go figure, they would emerge near the top of the heap 2 decades later as more reliable than ss tube. I always thought it was a very cool and functional design.
R1,
Plus the fact that they did/still out-perform all other headers! that's why I have 2 new sets sitting in my garage, I'm going to get with JP, I have an idea!:whistle:

AIR TIME 02-11-2012 01:10 PM
Originally Posted by h20 toie (Post 3590496)
Thats kind of why i have been debating going to American Hi-tek
http://www.american-hi-tek.com/

do i wait until i damage a motor or just spend the money now and not worry about it
no bargin at 6000, for long tails. hardin marine big tube headers thru transom tails are less than that. SM gen 3s are a great exhaust with no or maybe a few hp loss of power. put it would be great to here what Paradox has in mind.

43sv 02-11-2012 08:56 PM
Have had great success with stainless marine gen3 they make the same power on mild motors, and more power on big blower motors. No reason to even think about any other header. Have to get over the look and you will be fine. These tests were done on dyno

FIXX 02-24-2012 05:15 PM
So what'sthe scoop?
 
Originally Posted by PARADOX (Post 3615137)
YOu'r on the right track bud. :) :drink:
Did you have any takers on the idea?

the deep 02-24-2012 07:36 PM
What's shakin . Are you busy ciferin a design or just lickin em .:whistle:

Car Biz 02-13-2013 06:29 PM
Paradox what ever came of this idea you had?

the deep 02-13-2013 09:10 PM
Fill the water jackets with space shuttle ceramics and call it a day . :thankyouthankyou:

Control Freak 32 11-14-2013 04:02 PM
Any updates on this concept


All times are GMT -5. The time now is 07:03 AM.
Page 9 of 10
« First
7
8
9
10
Show 40 post(s) from this thread on one page


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.