18' powerplay hull expectations..
#101
Registered
Re: 18' powerplay hull expectations..
hey nice picture. coulded see past the glassies eyes. and whats with the guy on your left, you player you. ha ha
with that said you look the same. i guess age has treated you well.
todd
with that said you look the same. i guess age has treated you well.
todd
#102
Registered
Re: 18' powerplay hull expectations..
It's tough to age when your pickled Just went on the DONZI site and still wont let me post.There is a guy on there that goes by the name Freeplay that just bought a Baron a while back and had a new interior made,could you try to talk to him and see if he will tell you where he had his done and how much he paid,thats the only thing thats holding my boat up and after the last two experiences i had getting interiors done around here i don't want to deal with any more in this area.
#104
Gone Fishin'
Charter Member
Join Date: Nov 2000
Location: Grand Rapids/Holland/Grand Haven
Posts: 7,408
Likes: 0
Received 0 Likes
on
0 Posts
Re: 18' powerplay hull expectations..
What's a BH drive?
__________________
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
#107
Gone Fishin'
Charter Member
Join Date: Nov 2000
Location: Grand Rapids/Holland/Grand Haven
Posts: 7,408
Likes: 0
Received 0 Likes
on
0 Posts
Re: 18' powerplay hull expectations..
Originally Posted by boatnt
BlackHawk.
__________________
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
#109
Registered
Re: 18' powerplay hull expectations..
Yea,but i think they are a lot more efficient ,especially on this design.Travis when you get a chance could you give a us a full rundown of what you been doing to your motors and what kind of speed and rpm's and prop sizes you have done over your many seasons of modifications please.BARONMARINE I still have not gotten an answer from you about FLORIDA.Any luck with that guy on DONZI.net,if you could just get me an Email address or phone number i can handle it ,would appreciate it ,dragging the trailer queen over to the shop tomorrow and gonna try an and get her ready for a ride.Dave wesseldyk was down here and cranked up the blown 1000s in the skater at the shop ,got me kinda fired up again,gonna make time if i gotta quit my OSO addiction.
#110
Registered
Thread Starter
Join Date: Oct 2000
Location: On the river
Posts: 3,372
Likes: 0
Received 0 Likes
on
0 Posts
Re: 18' powerplay hull expectations..
tommymonza.. here is some info. Can't remember too much its been a while. Heres a little info. Its winter, snowmobile stuff in my head.
1st motor.
2bolt main block
eagle forged stroker crank
eagle 3D H-beam rods
SRP dished pistons, 9.8:1
clevite H-series bearings
cast iron vortec heads, machined for screw in studs, guideplates, and guides machined down to be able to run more lift.
crane gold roller rockers, 1.6
hydraulic roller cam, 222/230 duration, .542/.563 lift on a 112.
full crane roller valvetrain
edelbrock air gap intake
750 holley carb
EMI exhaust, cast risers.
stock ignition
custom oil pan.
big block chevy oil cooler
max hp @ 5200 rpm
good solid 400+ hp. Took boat from stock 58 to 70.1 mph on gps.
2nd motor
New 4bolt 383 block from GM
eagle forged stroker crank
eagle 3D H-beam rods
JE domed pistons, 10.6:1
clevite H-series bearings
AFR heads, 210cc CNC ported, cut to 68cc, set up heads myself
head studs
ferrea valves
full crane roller valvetrain
crane gold rockers 1.6 ratio
crane stud girdle
hydraulic roller cam 234/242 duration, .574/.595 lift on a 112
edelbrock victor jr intake
750 holley carb
EMI exhaust, with stainless tube risers.
stock ignition
custom oil pan
eddie marine biggest oil cooler
max hp @ 5500 rpm
good for about 500-510 hp. took boat from 70.1 to 74.4 on gps.
3rd motor
4bolt 383 block from GM
eagle forged stroker crank
eagle 3D H-beam rods
JE pistons, domed, 12.7:1
clevite H-series bearings
AFR heads, 210cc CNC ported, cut to 68cc, set up heads myself
new valve job and new valve springs
head studs
ferrea valves
full crane roller valvetrain
crane gold rockers 1.6 ratio
crane stud girdle
Solid roller cam, 250/258 duration, .598/.598 lift
edelbrock victor jr intake
750 holley
EMI exhaust, stainless tube risers
max hp @ 6000 rpm
stock ignition
custom oi pan
eddie marine biggest oil cooler
is suppose to be around 570 hp, just guessing
took boat from 74.4 to 78.9 on gps
it helped to I just found my motor notebook, has all my goodies and notes in it
1st motor.
2bolt main block
eagle forged stroker crank
eagle 3D H-beam rods
SRP dished pistons, 9.8:1
clevite H-series bearings
cast iron vortec heads, machined for screw in studs, guideplates, and guides machined down to be able to run more lift.
crane gold roller rockers, 1.6
hydraulic roller cam, 222/230 duration, .542/.563 lift on a 112.
full crane roller valvetrain
edelbrock air gap intake
750 holley carb
EMI exhaust, cast risers.
stock ignition
custom oil pan.
big block chevy oil cooler
max hp @ 5200 rpm
good solid 400+ hp. Took boat from stock 58 to 70.1 mph on gps.
2nd motor
New 4bolt 383 block from GM
eagle forged stroker crank
eagle 3D H-beam rods
JE domed pistons, 10.6:1
clevite H-series bearings
AFR heads, 210cc CNC ported, cut to 68cc, set up heads myself
head studs
ferrea valves
full crane roller valvetrain
crane gold rockers 1.6 ratio
crane stud girdle
hydraulic roller cam 234/242 duration, .574/.595 lift on a 112
edelbrock victor jr intake
750 holley carb
EMI exhaust, with stainless tube risers.
stock ignition
custom oil pan
eddie marine biggest oil cooler
max hp @ 5500 rpm
good for about 500-510 hp. took boat from 70.1 to 74.4 on gps.
3rd motor
4bolt 383 block from GM
eagle forged stroker crank
eagle 3D H-beam rods
JE pistons, domed, 12.7:1
clevite H-series bearings
AFR heads, 210cc CNC ported, cut to 68cc, set up heads myself
new valve job and new valve springs
head studs
ferrea valves
full crane roller valvetrain
crane gold rockers 1.6 ratio
crane stud girdle
Solid roller cam, 250/258 duration, .598/.598 lift
edelbrock victor jr intake
750 holley
EMI exhaust, stainless tube risers
max hp @ 6000 rpm
stock ignition
custom oi pan
eddie marine biggest oil cooler
is suppose to be around 570 hp, just guessing
took boat from 74.4 to 78.9 on gps
it helped to I just found my motor notebook, has all my goodies and notes in it