Notices
General Boating Discussion

Arneson Rocker Tabs.....

Thread Tools
 
Old 12-31-2002 | 07:58 AM
  #1  
hoghead's Avatar
Thread Starter
Registered
 
Joined: Feb 2002
Posts: 727
Likes: 0
From: Melbourne Beach, FL
Question Arneson Rocker Tabs.....

Anyone install a set of these?? If so ....what were the results. Also, what does a set of these usually cost?
hoghead is offline  
Reply
Old 12-31-2002 | 08:17 AM
  #2  
36spectre's Avatar
Registered User
 
Joined: Apr 2001
Posts: 589
Likes: 0
From: Princeton, new jersey
Default

Had them on my 36 Spectre for about a day. They nearly shook the boat apart. They seem to up set the water flow across the prop and it really upset the boat. Took us all day to find out that the rockers were to blame I really wish that they had worked cause they did a great job in changing the attitude of the boat at speeds below 100. Once the boat hit the higher hundreds the vibration was dangerous. Good luck OTTO
36spectre is offline  
Reply
Old 12-31-2002 | 08:17 AM
  #3  
36spectre's Avatar
Registered User
 
Joined: Apr 2001
Posts: 589
Likes: 0
From: Princeton, new jersey
Default

Had them on my 36 Spectre for about a day. They nearly shook the boat apart. They seem to up set the water flow across the prop and it really upset the boat. Took us all day to find out that the rockers were to blame I really wish that they had worked cause they did a great job in changing the attitude of the boat at speeds below 100. Once the boat hit the higher hundreds the vibration was dangerous. Good luck OTTO
36spectre is offline  
Reply
Old 12-31-2002 | 08:18 AM
  #4  
36spectre's Avatar
Registered User
 
Joined: Apr 2001
Posts: 589
Likes: 0
From: Princeton, new jersey
Default

How did I do that????
36spectre is offline  
Reply
Old 12-31-2002 | 08:23 AM
  #5  
Mike J
Guest
 
Posts: n/a
Default

I was involved in a project boat
a few years ago on a 29ft V.
Inserts were supplied before the
Boat was laid up in the mold.
The boat ran very well.
The rockers are under the boat
even with the bottom, Not added
to the transom.
You could call Paul at PSA Marine
In the Oakland Ca. Area, He ran
the Boat.
PSA Marine 510-865-4191
Mike J.
 
Reply
Old 12-31-2002 | 08:24 AM
  #6  
36spectre's Avatar
Registered User
 
Joined: Apr 2001
Posts: 589
Likes: 0
From: Princeton, new jersey
Default

Also they were great about the return and very helpfull with advive on how to possibly make them work. Nice people and no problem with refunding me money with a smile. I would deal with them again for sure. OTTO
36spectre is offline  
Reply
Old 12-31-2002 | 08:24 AM
  #7  
hoghead's Avatar
Thread Starter
Registered
 
Joined: Feb 2002
Posts: 727
Likes: 0
From: Melbourne Beach, FL
Default

How about installed on a V-hull??
hoghead is offline  
Reply
Old 12-31-2002 | 08:32 AM
  #8  
D_Casten's Avatar
Registered
 
Joined: Oct 2000
Posts: 126
Likes: 0
From: N41 41.709' - W93 41.916'
Default

We cut the hook out of our hull and added a set. The rocker portion does work as they claim. Our max MPH didn’t increase much but we can carry the speed much better with a load up front. (open bow boat) or when full of fuel.

I believe list is $3,500

D_Casten is offline  
Reply
Old 12-31-2002 | 08:33 AM
  #9  
Offshore Addiction
Guest
 
Posts: n/a
Default

audaticity should chine in,I think the factory two guys had some good luck with theres,but him or treadwell would be the ones to ask.........
 
Reply
Old 12-31-2002 | 10:30 AM
  #10  
Registered
25 Year Member
 
Joined: Oct 2000
Posts: 1,181
Likes: 2
From: Cora
Default

I think Tres Martin used them on the Glaidator that won the World and National F2.
Brad is offline  
Reply


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.