Plastic 1/2 hole wedge for Bravo...front or to the back ?
02-23-2006 | 08:57 PM
#1
Thread Starter
Registered
Joined: May 2002
Posts: 860
Likes: 0
From: North of the Border
Plastic 1/2 hole wedge for Bravo...front or to the back ?
Newer Bravos use a plastic 1/2 hole wedge that also goes in that hole to postion the shaft either to the front or to the back of the oblonged slot/hole depending if the drive is to be used on a cruiser or a non- cruiser application.
I never remember on wich side the wedge go ...... in front or rear of the pin ?
Thank's to take time to respond me
I prepared the Outlaw to go to Miami in 6 Day .....and if the weather is on our side ....cross to Exuma Island !!!!!!!!
02-23-2006 | 09:00 PM
#2
Gold Member
Joined: Jan 2001
Posts: 2,123
Likes: 1
From: Brooklyn Park, Md USA
Re: Plastic 1/2 hole wedge for Bravo...front or to the back ?
Usually to the front on a Bravo 1, if its a Bravo 3 it goes to the back.
John S.
Plus it also depends on how much negitive trim you want or if you dont want the drive to trim all the way up as far as it could go.
Go with the front one.
John S.
Plus it also depends on how much negitive trim you want or if you dont want the drive to trim all the way up as far as it could go.
Go with the front one.
02-23-2006 | 09:07 PM
#3
Registered
Joined: Apr 2005
Posts: 2,675
Likes: 0
From: KENT ISLAND, MARYLAND
Re: Plastic 1/2 hole wedge for Bravo...front or to the back ?
Originally Posted by Pwrbt33
Usually to the front on a Bravo 1, if its a Bravo 3 it goes to the back.
John S.
Plus it also depends on how much negitive trim you want or if you dont want the drive to trim all the way up as far as it could go.
Go with the front one.
John S.
Plus it also depends on how much negitive trim you want or if you dont want the drive to trim all the way up as far as it could go.
Go with the front one.
took the words right out of my mouth as usual on the money!!!
02-23-2006 | 09:10 PM
#4
Thread Starter
Registered
Joined: May 2002
Posts: 860
Likes: 0
From: North of the Border
Re: Plastic 1/2 hole wedge for Bravo...front or to the back ?
This board Rock ......3 minute delay before respond 
Thank's alot John ... i will put my drive on my boat tomorow night .... and with your info it's going to be easier
p.s. on your avatar i see Md ...it's Maryland ?? cause on my road trip to Florida i have to pass the Delaware bridge (or Tunnel) did you know i have the right to pass there with my boat ? Thank's again
Thank's alot John ... i will put my drive on my boat tomorow night .... and with your info it's going to be easier
p.s. on your avatar i see Md ...it's Maryland ?? cause on my road trip to Florida i have to pass the Delaware bridge (or Tunnel) did you know i have the right to pass there with my boat ? Thank's again
02-23-2006 | 09:15 PM
#5
Gold Member
Joined: Jan 2001
Posts: 2,123
Likes: 1
From: Brooklyn Park, Md USA
Re: Plastic 1/2 hole wedge for Bravo...front or to the back ?
Thats cool! Yup, its Maryland, our shop is in Grasonville, Maryland. Right close to Red Eyes dock bar and the Chesapeake Bay Bridge.
Have a great trip!
John S.
Have a great trip!
John S.
Thread
Thread Starter
Forum
Replies
Last Post
Cattitude
Drives and Lower Units
2
05-10-2007 11:20 AM
