Offshoreonly.com
Page 38 of 52
« First
28
36
37
38
39
40
48
Last »
Show 40 post(s) from this thread on one page

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   General Q & A (https://www.offshoreonly.com/forums/general-q-20/)
-   -   EFI for everyone (https://www.offshoreonly.com/forums/general-q/265811-efi-everyone.html)

hadleycat 08-20-2014 10:13 PM
Originally Posted by HaxbySpeed (Post 4175096)
You don't need to spend the whole day, it'll do it in 10 minutes. Go drive around once you're up to temperature, and hit as many load points and you can, over trimmed, under trimmed, hard accel from various rpm's, easy accel, try to hold each rpm point for 5 to 10 seconds. Then stop, transfer learn table to base and hit smooth. Now turn the learn gain down to 25% and do it again. If everything is + or - two to three percent then you can turn off the learn. If it isn't, transfer, smooth, and do it again. Once that's done you can turn the closed loop off, or if your O2's staying nice and dry, just turn the learn off and set your closed loop correction to 10% and let er rip.
Awesome, thanks Alex

GPM 08-21-2014 06:17 PM
Does this mean the Holley self tune doesn't actually tune real time, you have to stop and load it manually ?

HaxbySpeed 08-21-2014 06:57 PM
Originally Posted by GPM (Post 4175599)
Does this mean the Holley self tune doesn't actually tune real time, you have to stop and load it manually ?
No, it tunes real time, incredibly fast. It just shows you what it has learned, which is better then overwriting your base map wether you like it or not. You can erase what it's learned, just leave it, or transfer it permanently to the base map any time you like.

GPM 08-21-2014 08:08 PM
So what would the motor be running on until you transfer, what's actually on the map or what it's learned ?

HaxbySpeed 08-21-2014 08:50 PM
Originally Posted by GPM (Post 4175645)
So what would the motor be running on until you transfer, what's actually on the map or what it's learned ?
Both. The base map, plus whatever percentage it's had to add or subtract in order to maintain the commanded AFR. It just shows you the percentage on a different table. The benefit is, say if you had a misfire at a certain rpm and the computer added a bunch of fuel, thinking it was lean. You don't want that section corrupting your base map, so you can erase it, or you could transfer it and then remove the percentage in the affected section. When you transfer it, it shows the exact cells in the base map that were adjusted by marking them with a green dot. This allows you to do some more smoothing in the untuned areas if you want. It will also save your base map if your O2 sensor takes a dump while it's in learn mode.

GPM 08-21-2014 09:34 PM
So most likely you would transfer the map and then run the motor through different RPM ranges to verify the tune is accurate ?

ezstriper 08-22-2014 11:20 AM
sure wish we could get a 02 to live in these damn lightning silent choice headers, just built a dump tube with a angle cut piece in the header, and looped around back into Y-pipe, so 02 was out of the header...lasted about 2 mins at cruise 3500...when I pulled it out a few days later...02 had rust so water even got out to the there...

hadleycat 08-22-2014 11:40 AM
Originally Posted by ezstriper (Post 4175941)
sure wish we could get a 02 to live in these damn lightning silent choice headers, just built a dump tube with a angle cut piece in the header, and looped around back into Y-pipe, so 02 was out of the header...lasted about 2 mins at cruise 3500...when I pulled it out a few days later...02 had rust so water even got out to the there...
Sounds like a great idea, Thats a drag that it didnt work.

502ss 08-31-2014 09:54 AM
Been doing a bunch of research in preparation for my efi journey this winter. Been reading every forum post over at forums.holly.com in the efi section. Stumbled across a post about moving the o2 sensor out of the exhaust stream. It looks like this has been done with great success! Maybe it would help with some of those having reversion issues?

http://www.innovatemotorsports.com/x...cat=250&page=2

Cole2534 08-31-2014 10:05 AM
So what's the cost to go from an MPI setup to the holley setup?


All times are GMT -5. The time now is 12:02 AM.
Page 38 of 52
« First
28
36
37
38
39
40
48
Last »
Show 40 post(s) from this thread on one page


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.