Offshoreonly.com

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   General Q & A (https://www.offshoreonly.com/forums/general-q-20/)
-   -   Playboy getting Head (https://www.offshoreonly.com/forums/general-q/346673-playboy-getting-head.html)

cigrocket 05-14-2017 02:15 PM

5 Attachment(s)
Some progress on the heads

adk61 05-14-2017 07:25 PM

we be rockin and rollin on these badboys!!! Playboy's gettin head alright!!! :lolhit:

cigrocket 05-17-2017 09:11 AM

3 Attachment(s)
Waiting on some parts from Eddie Young and also Al working on the heads.

My Wife de- greased the bilge, roughed it up with 180 grit and put down 2 coats of paint. Looking good.

Crude Intentions 05-17-2017 10:56 AM

Looks great. What paint did you use in the bilge?

cigrocket 05-17-2017 11:07 AM


Originally Posted by I.C.U.Lookin (Post 4554760)
Looks great. What paint did you use in the bilge?

This time I decided to Try Rustoleum with the Hardener from Valspar. Many have used it and have had good success.

Last Boat I had...the Top Gun...I used Bilge Coat, I found that it turned yellow and faded pretty fast and despite good prep seemed to take forever to cure

The Mistress I had, I did Red in Awlgrip, It was harder to work with and on the Spendy Side.

So we shall see. The white is nice and bright, and that is what I like, it was easy to apply and flowed really nice. I tend to keep a really clean bilge so I assume it will hold up well. I mixed up a 1/2 quart at a time with the hardener. So far I am pleased, but I guess time will tell.

The prep was Cleaned Bilge with Purple Industrial Degreaser from Tractor Supply with a pump sprayer. Power Washed. Then Light sanding with flexible sanding blocks 180 grit. Finally wiped everything down again with acetone and tac cloths.

Applied the Rustoleum Bright White. Brush and Small Roller.

Padraig 05-17-2017 11:11 AM


Originally Posted by cigrocket (Post 4554729)
Waiting on some parts from Eddie Young and also Al working on the heads.

My Wife de- greased the bilge, roughed it up with 180 grit and put down 2 coats of paint. Looking good.

Can't go wrong with Eddie Young. What is he supplying?
Don't forget to register for the Battleship, discounted registration is coming to a close. The wife just did ours.

Padraig

cigrocket 05-17-2017 11:13 AM


Originally Posted by Padraig (Post 4554767)
Can't go wrong with Eddie Young. What is he supplying?
Don't forget to register for the Battleship, discounted registration is coming to a close. The wife just did ours.

Padraig

I am getting CAMS and LIFTERS from him... He is also doing the EFI TUNE and DYNO. I will be venturing down to TENN.

I will be going to Battleship run, Hopefully boat will be done or I will be hitching a ride

Padraig 05-17-2017 11:37 AM


Originally Posted by cigrocket (Post 4554769)
I am getting CAMS and LIFTERS from him... He is also doing the EFI TUNE and DYNO. I will be venturing down to TENN.

I will be going to Battleship run, Hopefully boat will be done or I will be hitching a ride

Long ride to Tennessee but you will get a good tune. Besides a talented engine builder, he is a good guy.

Padraig

kreed 05-19-2017 07:15 AM

Is there an ETA on these engines? As always, I commend you on the wife pic!

cigrocket 05-22-2017 11:24 AM

Spoke with Big Al yesterday on the phone, he is performing the final hand porting and assembly. The Heads are scheduled to be done this week!. Can't wait to see them!


All times are GMT -5. The time now is 02:42 PM.


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.