Go Back  Offshoreonly.com > Technical > General Q & A
575 SCi ECM tune >

575 SCi ECM tune

Notices

575 SCi ECM tune

Old 04-29-2020, 11:19 AM
  #1  
Registered
Thread Starter
 
Join Date: Sep 2012
Location: Denver, CO
Posts: 131
Likes: 0
Received 0 Likes on 0 Posts
Default 575 SCi ECM tune

Does anyone know who tunes the 575 anymore? Obviously ASM isn't an option due to the myriad of bad experiences. Does anyone know of a software that allows the user to tune?
PowerAddict is offline  
Old 04-29-2020, 12:33 PM
  #2  
Registered
iTrader: (1)
 
Join Date: Nov 2009
Location: KY
Posts: 3,616
Received 321 Likes on 244 Posts
Default

Stock tunes should not be an issue, but if your talking about on the boat, then there is MEFIburn and a couple here on OSO maybe
AllDodge is offline  
The following users liked this post:
articfriends (04-30-2020)
Old 04-29-2020, 12:46 PM
  #3  
Registered
iTrader: (2)
 
Join Date: Aug 2010
Location: Cape Coral FL
Posts: 1,801
Likes: 0
Received 162 Likes on 102 Posts
Default

I have a few 575 tunes on an old computer. What exactly are you trying to do?
snapmorgan is offline  
Old 04-30-2020, 03:47 PM
  #4  
Registered
Thread Starter
 
Join Date: Sep 2012
Location: Denver, CO
Posts: 131
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by snapmorgan View Post
I have a few 575 tunes on an old computer. What exactly are you trying to do?

I can only assume the PO did not tune the ECU when he added the small pulley and SuperChiller. I think this because It seems to still have a lot of the same manners others say these have in stock form. So, I suppose the standard ECM re-flash with the Boost kit would probalby suffice. Rev limit a little higher would be nice.

Can you use MEFI Burn with these then, Snap?
PowerAddict is offline  
Old 05-01-2020, 07:28 AM
  #5  
Platinum Member
Platinum Member
iTrader: (1)
 
articfriends's Avatar
 
Join Date: Jun 2004
Location: Frankenmuth
Posts: 6,634
Received 228 Likes on 115 Posts
Default

Originally Posted by PowerAddict View Post
I can only assume the PO did not tune the ECU when he added the small pulley and SuperChiller. I think this because It seems to still have a lot of the same manners others say these have in stock form. So, I suppose the standard ECM re-flash with the Boost kit would probalby suffice. Rev limit a little higher would be nice.

Can you use MEFI Burn with these then, Snap?
Yes, mefiburn will work with it. Id ask Bob at mefiburn IF he can unlock the ecu before buying the program though, starting over vs modifying are two different things. Keep in mind too, IF a 3rd party tuned it at some point and locked ecu, you will need to start over also as you will NOT be able to tune it, Smitty
articfriends is offline  
Old 05-08-2020, 12:50 PM
  #6  
Registered
 
Join Date: Jan 2015
Location: Maryland
Posts: 10
Likes: 0
Received 0 Likes on 0 Posts
Default

Any luck unlocking your ECU? I have the same issues. Running the blower and TBI setup on my 454s, need to adjust fuel trim.
NastyHabbitSR1 is offline  
Old 05-08-2020, 01:35 PM
  #7  
BUP
Banned
iTrader: (9)
 
Join Date: Jul 2011
Location: Ft. Worth TX
Posts: 9,595
Likes: 0
Received 37 Likes on 32 Posts
Default

I would have the ecms tested - the injectors drivers are known to have issues and cause rich to very rich conditions also what are your map sensor readings ? what are your fuel pressure readings ? what are your coolant temp readings ?


Let me know if I can help with the ecm side and a scan report
BUP is offline  
Old 05-08-2020, 03:46 PM
  #8  
Registered
 
Join Date: Jan 2015
Location: Maryland
Posts: 10
Likes: 0
Received 0 Likes on 0 Posts
Default

BUP- I havnt actually run mine yet almost done building, probably a couple weeks out. I have decent size roller cams and everyone I have talked to said they are rich from the factory. I replaced all sensors and performed a ring out of the harnesses, not worried about that. My intention was to buy MEFI burn to tune, then I stumbled upon the fact merc locked the ecm. I am looking for the code to unlock, have someone unlock it or get a generic canned tune I can start with. I donít mind purchasing the tune and unlock but I would require the ecm to remain unlocked so i can finish tuning with a wide band.
NastyHabbitSR1 is offline  
Old 05-08-2020, 03:59 PM
  #9  
Registered
iTrader: (1)
 
Join Date: Nov 2009
Location: KY
Posts: 3,616
Received 321 Likes on 244 Posts
Default

intention was to buy MEFI burn to tune, then I stumbled upon the fact merc locked the ecm.
Then your good. My guess is Bob at MEFI burn or another will have the base tune. All you need to do is erase the tune (if it is locked) then reload the base tune. The MEFI 1 and 2 didn't come locked, and not real sure but the 3 may not be locked either. Eddie Young knows would know
AllDodge is offline  
Old 05-11-2020, 07:18 AM
  #10  
Registered
iTrader: (1)
 
Join Date: Jul 2007
Location: MI
Posts: 2,636
Received 9 Likes on 5 Posts
Default

Originally Posted by snapmorgan View Post
I have a few 575 tunes on an old computer. What exactly are you trying to do?
Joe, do you have any 575 stuff left? I just purchased two more of them for my DCB and I am looking for some 3.5" pulleys
JRider is offline  

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.