Offshoreonly.com
Page 2 of 3
1
2
3
Show 40 post(s) from this thread on one page

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   General Q & A (https://www.offshoreonly.com/forums/general-q-20/)
-   -   Camshaft Recommendations (https://www.offshoreonly.com/forums/general-q/383967-camshaft-recommendations.html)

jeffswav 10-20-2024 11:53 AM
See quote

jeffswav 10-20-2024 11:55 AM
See quote

jeffswav 10-20-2024 11:59 AM
Originally Posted by Smitty275 (Post 4912066)
Chris Straub in East Tennessee is highly regarded by a lot of builders. I'll be getting my next one from him to try out.
Actually just talked to him on Friday. Said he could get me more torque and HP with better fuel economy. Recommended a cam that was actually smaller than what I expected.

jeffswav 10-20-2024 12:01 PM
Lunati has removed most of its BBC cams off the website. Not sure whats up with that.
 
Originally Posted by F-2 Speedy (Post 4911705)
Bullet cams is talked about here, personally Ive not used them, Lunati , TCM in Cali has some off the shelf cams but I dont think they grind them. I had cam motion do a custom grind for some 540's but that was 9 years a go
Lunati has removed most of its BBC cams off the website. Not sure whats up with that.

JaniH 10-20-2024 12:45 PM
Originally Posted by Smitty275 (Post 4912066)
Chris Straub in East Tennessee is highly regarded by a lot of builders. I'll be getting my next one from him to try out.
I had Chris to design a custom cam to my old engine, and highly recomend his custom cams! Hi knows how to get the most out of your not so good cylinder heads. My engine made 528 dyno prooven hp with ported peanut port heads.

JaniH 10-20-2024 12:47 PM
Originally Posted by JaniH (Post 4912076)
I had Chris to design a custom cam to my old engine, and highly recomend his custom cams! Hi knows how to get the most out of your not so good cylinder heads. My engine made 528 dyno prooven hp with ported peanut port heads.
quited to wrong post, sorry.

JaniH 10-20-2024 12:51 PM
Originally Posted by jeffswav (Post 4912072)
Actually just talked to him on Friday. Said he could get me more torque and HP with better fuel economy. Recommended a cam that was actually smaller than what I expected.
I had Chris to design a custom cam to my old engine, and highly recomend his custom cams! Hi knows how to get the most out of your not so good cylinder heads. My engine made 528 dyno prooven hp with ported peanut port heads.

jeffswav 10-20-2024 01:03 PM
Originally Posted by JaniH (Post 4912078)
I had Chris to design a custom cam to my old engine, and highly recomend his custom cams! Hi knows how to get the most out of your not so good cylinder heads. My engine made 528 dyno prooven hp with ported peanut port heads.
I have AFR clone heads with AFR valves. I reused the cam on my last refresh that was setup for GM large ovals and lower compression. Shooting for 600+ HP

SB 10-20-2024 06:05 PM
Bullet/Comp/Teague, etc, etc
Straub was banned from this forum. For legit reasons.
Caveat Emptor.

sutphen 30 10-20-2024 11:05 PM
Originally Posted by JaniH (Post 4912078)
I had Chris to design a custom cam to my old engine, and highly recomend his custom cams! Hi knows how to get the most out of your not so good cylinder heads. My engine made 528 dyno prooven hp with ported peanut port heads.
what were the cam specs on this magical engine,,I can compare it to my 524 and 527hp cast iron oval port headed 454's.


All times are GMT -5. The time now is 06:20 AM.
Page 2 of 3
1
2
3
Show 40 post(s) from this thread on one page


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.