Go Back  Offshoreonly.com > Technical > General Q & A
eddie marine Thumper install >

eddie marine Thumper install

Notices

eddie marine Thumper install

Old 06-30-2004, 10:49 PM
  #1  
Registered
Thread Starter
 
MiamiVice's Avatar
 
Join Date: Jan 2004
Location: Miami, Florida
Posts: 94
Likes: 0
Received 0 Likes on 0 Posts
Default eddie marine Thumper install

Has anybody installed the Eddie Marine Thumpers with Silent Choice elbows. I bought a set and was going to tackle the job myself. Any tips? I have a Fountain 32 Fever with twin 502 mag mpi. Not a whole lot of room in the engine compartment.
MiamiVice is offline  
Old 07-02-2004, 11:34 AM
  #2  
Registered
 
Join Date: Jul 2001
Location: oshawa ontario
Posts: 4,825
Received 84 Likes on 20 Posts
Default Re: eddie marine Thumper install

Imco makes the Thumpers
pullmytrigger is offline  
Old 07-02-2004, 09:21 PM
  #3  
Registered
Thread Starter
 
MiamiVice's Avatar
 
Join Date: Jan 2004
Location: Miami, Florida
Posts: 94
Likes: 0
Received 0 Likes on 0 Posts
Default Re: eddie marine Thumper install

Ok, I mean the Eddie Marine exhaust with chrome elbows. I also was looking at the Thumpers before I purchased these from Too Old.
MiamiVice is offline  
Old 07-04-2004, 09:14 PM
  #4  
Registered
 
H2Xmark's Avatar
 
Join Date: Apr 2001
Location: beaumont tx
Posts: 1,703
Likes: 0
Received 0 Likes on 0 Posts
Default Re: eddie marine Thumper install

I installed the EMI thunder manifolds with the short stainless risers for cap. call[corsa]on my baja 29 outlaw with twin 454mag mpi's, do yourself one big favor and call IMCO and buy the longer oval hoses that go from the bottom Y pipe up to the silent choice divertor, the stock hoses or not really long enough, you could use them but you would not have much hose on each end of the pipe[also that is near the water line] for the double clamps, the new hose from IMCO also has new stainless clamps, make sure you also get the plates and angle brackets to hook up your shifter, computer box and oil filter bracket[my engines are VST] also the high pressure power steering hose on the back of the pump will hit the manifold by a small amount[ I put more of a bend in the stock hose to clear]also make sure you retorque the manifolds after you run it a few hours, they torque to 35 ft. lbs.
H2Xmark is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
zx14
General Boating Discussion
32
06-11-2008 11:50 AM
Bottoms Up
General Boating Discussion
1
04-28-2007 10:53 PM
Allatoonaoutlaw
General Q & A
1
04-01-2007 08:27 AM
onesickpantera
General Q & A
6
10-23-2006 04:34 AM
nordic95
General Q & A
50
05-22-2006 05:57 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Quick Reply: eddie marine Thumper install


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.