Finally done
#11
Registered
Thread Starter
Join Date: Nov 2002
Location: Bonita Springs, Florida
Posts: 3,029
Likes: 0
Received 1 Like
on
1 Post
Re: Finally done
580 cubes, roller cams, twin dominators, 1071 blowers, o-berg filters, dry sumped, aluminum dart heads, BDS chillers, arneson #8's , Rolla 32 x 17.5's.
Current plan is to splash it Friday morning in the Detroit area, do some final carb adjustments and run it across the lake about 40 miles to Port Clinton, Ohio.
Current plan is to splash it Friday morning in the Detroit area, do some final carb adjustments and run it across the lake about 40 miles to Port Clinton, Ohio.
#12
Registered
Thread Starter
Join Date: Nov 2002
Location: Bonita Springs, Florida
Posts: 3,029
Likes: 0
Received 1 Like
on
1 Post
Re: Finally done
Forgot to mention, almost every piece of metal on this boat has been powder coated including the blocks, heads, intakes, dash panels, drives, scatter shields and everything else that could be unscrewed/bolted in the cabin, cockpit, engine compartment, also including the cleats. The pullies etc are anodized. All the gauges have also been refinished
The trannies, starters and carbs are painted.
The trannies, starters and carbs are painted.
Last edited by expresscat39; 09-01-2004 at 06:08 AM.
#14
Platinum Member
Platinum Member
Re: Finally done
I have been watching this project, WOW!!!!! , and I can see all the pain staking efforts going into making this a better than new boat. Looks awesome, good luck with her, post some speeds when you get her broken in, Good Luck. Jeff
#16
Registered
Thread Starter
Join Date: Nov 2002
Location: Bonita Springs, Florida
Posts: 3,029
Likes: 0
Received 1 Like
on
1 Post
Re: Finally done
We cruised for 20-25 minutes at 70 mph. Then we started to crank it up slowly but surely watching the GPS at increments of 500 RPM. At just about 5500 the starboard engine's water temp went ballistic and we shut it down. At that point we were trucking at 110.6 according to the GPS tattle tale. WOT @ 6,000 r's we estimate 120 to 125 mph.
The port header on the starboard engine must have a blockage. We removed the header and shipped it to Stellings for inspection. We could still run it at 4,000 rpm but anything above resulted in the temperature building rapidly. The problem was only in the top two tubes. The bottom two were perfectly fine.
Hoping for good news today from Randy so we can get it back together and in the water Septermber 17th.
The port header on the starboard engine must have a blockage. We removed the header and shipped it to Stellings for inspection. We could still run it at 4,000 rpm but anything above resulted in the temperature building rapidly. The problem was only in the top two tubes. The bottom two were perfectly fine.
Hoping for good news today from Randy so we can get it back together and in the water Septermber 17th.
Last edited by expresscat39; 09-10-2004 at 11:14 AM.
#17
Re: Finally done
awsome boat E-cat. great #'s too, thats move'n right along. i have been on TizBads OceanX several times at speed. the thing is so big it reminds me of sitting on the roof of my garage . . . but at 100mph
__________________
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
#18
Registered
Thread Starter
Join Date: Nov 2002
Location: Bonita Springs, Florida
Posts: 3,029
Likes: 0
Received 1 Like
on
1 Post
Re: Finally done
Hi Dave. I saw Greg's at the Monroe LEOPA run. I was going to do the fall run but had a bad header. Did you go on that one?
Yea, it is a big party barge. Everybody gets on it thinks it is a 50 footer.
Yea, it is a big party barge. Everybody gets on it thinks it is a 50 footer.
#19
Re: Finally done
didnt make it to the fall run. actually i just ran around this end of the lake all weekend with no real agenda. was pretty cool just went hear an there, stayed on the boat from fri-sun. heard the run was great though, little bit to big a run for my lil'ol scorpion
ya mean those things arent 50 foot???
speak'n of 50's wonder when Rossi is gonna get the new 49 out. i have some spy pics around here somewhere
ya mean those things arent 50 foot???
speak'n of 50's wonder when Rossi is gonna get the new 49 out. i have some spy pics around here somewhere
__________________
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
Last edited by glassdave; 09-15-2004 at 11:55 PM.