Finally done
#52
Registered
Join Date: Feb 2001
Location: Norway (Ft Lauderdale)
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
Re: Finally done
Hi Mark !
The world is not so big,this is my boat.
It`s a bad pictures of the boat,the guy beefore me had
diesels in it,but he never change the gear ratio in the
Arnesons, he never got this right,It`s still the gas gear
ratios in the Arnesons from the time the boat had
big V8`s. I have to do this right,not only trying difrent
props,you know that`s never a happy ending.
502Magnum
The world is not so big,this is my boat.
It`s a bad pictures of the boat,the guy beefore me had
diesels in it,but he never change the gear ratio in the
Arnesons, he never got this right,It`s still the gas gear
ratios in the Arnesons from the time the boat had
big V8`s. I have to do this right,not only trying difrent
props,you know that`s never a happy ending.
502Magnum
#53
Registered
Join Date: Oct 2003
Location: Chicago, Illinois
Posts: 3,254
Likes: 0
Received 0 Likes
on
0 Posts
Re: Finally done
Try Rik at www.arnesonindustries.com
He is the big US rep. Twindisc in Racine, Wisconsin may have a local distributor for these parts in Norway. Diesels could be a great set-up. The 2 speed trans set-up might be the answer to get it on plane. What does the boat weight with Yanmars in the boat? I heard 2000 hours between tune-ups.
Mark
He is the big US rep. Twindisc in Racine, Wisconsin may have a local distributor for these parts in Norway. Diesels could be a great set-up. The 2 speed trans set-up might be the answer to get it on plane. What does the boat weight with Yanmars in the boat? I heard 2000 hours between tune-ups.
Mark
#54
Registered
Thread Starter
Join Date: Nov 2002
Location: Bonita Springs, Florida
Posts: 3,029
Likes: 0
Received 1 Like
on
1 Post
Re: Finally done
Originally Posted by 502 Magnum
Expresscat39, your boat looks great,the work and all, I`v allready
learnd alot from your project. I`m going to put Yanmar diesels with
2 speed tranis in mine OE 39 ,do you know where I can get a sett
of 1:1 gearing ratio for my Arnesons? I got the same ASD8 16`drop
as you,thanks.
502 Magnum
learnd alot from your project. I`m going to put Yanmar diesels with
2 speed tranis in mine OE 39 ,do you know where I can get a sett
of 1:1 gearing ratio for my Arnesons? I got the same ASD8 16`drop
as you,thanks.
502 Magnum
#55
Registered
Thread Starter
Join Date: Nov 2002
Location: Bonita Springs, Florida
Posts: 3,029
Likes: 0
Received 1 Like
on
1 Post
Re: Finally done
Originally Posted by expresscat39
I have a full extra set the 1:1's, gears, ratios sleeves, extra shafts, and 4 balde Rollas.
I also have the chains. Also there were two speeds in mine and I changed them back. If you do not have a lead on the trannies let me know. It moves the engines forward quite a bit.
Last edited by expresscat39; 10-25-2004 at 10:38 AM.
#56
Registered
Join Date: Feb 2001
Location: Norway (Ft Lauderdale)
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
Re: Finally done
Expresscat39 and Mark,thanks for friendly replys, I`m a gas motor man,
but I`ll give these 2 Yanmars a try,thanks for the adress Mark,and yes
they say the Yanmar 6LY2-STE`s are good motors.Expresscat39,it
sounds good to me aboat the gears,I`ll PM you.
502 Magnum
but I`ll give these 2 Yanmars a try,thanks for the adress Mark,and yes
they say the Yanmar 6LY2-STE`s are good motors.Expresscat39,it
sounds good to me aboat the gears,I`ll PM you.
502 Magnum
#57
Registered
Thread Starter
Join Date: Nov 2002
Location: Bonita Springs, Florida
Posts: 3,029
Likes: 0
Received 1 Like
on
1 Post
Re: Finally done
http://www.offshoreonly.com/forums/s...6&page=2&pp=30
Bjorn, here is an old thrread. Start at this point and read through.
Bjorn, here is an old thrread. Start at this point and read through.
#58
Registered
Join Date: Feb 2001
Location: Norway (Ft Lauderdale)
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
Re: Finally done
Hi Dennis ! Yea,I know this,but some stuff here is not
accurate,I think it can work prety good if I do it
right,but I know its not big V8`s.Have a good time.
Bjorn
accurate,I think it can work prety good if I do it
right,but I know its not big V8`s.Have a good time.
Bjorn