Any interest in a 3man 24' pantera?
05-31-2011, 11:36 AM
#1
Any interest in a 3man 24' pantera?
Same old story - work and life taking up too much time so something has to go.
Boat is the old No Limits raceboat raced by MER back in the day. Great boat with a TON of extra structural work done over the years. Think mini-Apache.
Will be listing it shortly but figured I'd give you guys first crack at it.
Boat is very solid just a couple cosmetic items. Boat has the following:
24' raceboat
add'l bulkhead in the bow
ballast tank
add'l stringer supports
TRS drive w/nosecone
BW trans
bellhousing w/cooler & coupler
dual ram steering with billet filter
large K-planes
latham controls
front and rear mounts
merc racing trim pumps (#6 style)
Also purchased some additional items:
-hydraulic helm from Imco
-9pin harness
-dash harness
-Gaffrig race edition guages - carbon fiber (black) face
-Lonseal flooring
-TRS transom assembly - spare (current one has a repaired gimbal ring)
Also, swapped out the junk trailer for a clean Eagle black steel tandem trailer setup for this hull.
No motor but do a have a 540hp motor I could sell.
Built to handle the big stuff so this boat would be a blast whether as a raceboat or pleasure. A bit tough to price as there's not much out there to compare it to.
Asking $13,500 minus motor
Open to offers.
Pics are a bit old but they give you an idea....
Boat is the old No Limits raceboat raced by MER back in the day. Great boat with a TON of extra structural work done over the years. Think mini-Apache.
Will be listing it shortly but figured I'd give you guys first crack at it.
Boat is very solid just a couple cosmetic items. Boat has the following:
24' raceboat
add'l bulkhead in the bow
ballast tank
add'l stringer supports
TRS drive w/nosecone
BW trans
bellhousing w/cooler & coupler
dual ram steering with billet filter
large K-planes
latham controls
front and rear mounts
merc racing trim pumps (#6 style)
Also purchased some additional items:
-hydraulic helm from Imco
-9pin harness
-dash harness
-Gaffrig race edition guages - carbon fiber (black) face
-Lonseal flooring
-TRS transom assembly - spare (current one has a repaired gimbal ring)
Also, swapped out the junk trailer for a clean Eagle black steel tandem trailer setup for this hull.
No motor but do a have a 540hp motor I could sell.
Built to handle the big stuff so this boat would be a blast whether as a raceboat or pleasure. A bit tough to price as there's not much out there to compare it to.
Asking $13,500 minus motor
Open to offers.
Pics are a bit old but they give you an idea....
Last edited by fantastixvoyage; 05-31-2011 at 11:44 AM.
06-01-2011, 11:12 AM
#4
Sure is! Plans were to run in 5 or 6 since it is a perfect boat for that. Can run hard without having to worry about the boat coming apart. Would make a fun day boat too for the same reason. I'll try to post a video of it running. Ran very hooked up and flat with this configuration.
06-02-2011, 09:49 PM
#9
Agree! I was amazed at the overall condition of the boat. Sucks to see it go but just too many boats and no time. Would be an EASY job to get it back on the water.
If I could sell it quick I'll take $11,500 as it sits. Hell I'll even toss in everything but the guages.
If I could sell it quick I'll take $11,500 as it sits. Hell I'll even toss in everything but the guages.
06-03-2011, 12:24 AM
#10
Here is the swap shop ad, going in classifieds on multiple sites over the weekend.
http://www.offshoreonly.com/forums/s...us-engine.html
http://www.offshoreonly.com/forums/s...us-engine.html
