Offshoreonly.com - Search Results

Search: Posts Made By: MojoBoss

Showing results 1 to 9 of 9
Search took 0.01 seconds.

Forum: Drives and Lower Units

03-15-2015, 12:26 PM

Replies: 5

Bravo 1 gear lube in bilge

Views: 3,999

Posted By MojoBoss

Bravo 1 gear lube in bilge

Bravo 1 gear lube in bilge.
Pulled my Out drive and found Gear oil in bellows. I suspect that the yoke seal has failed but is there anything I should be looking for that may had caused this to...

Forum: Do It Yourself, Boating on a Budget

12-16-2013, 07:30 PM

Replies: 5

Brovo1 OW220-Water and drive lube in bilge

Views: 1,598

Posted By MojoBoss

I have just pulled the lower unit and found the...

I have just pulled the lower unit and found the shaft bellows is half full of gear lube.
Looks like the seal let go some time ago!
I couldn't see how the gear lube could travel the drive shaft and...

Forum: Do It Yourself, Boating on a Budget

10-16-2012, 08:31 PM

Replies: 5

Brovo1 OW220-Water and drive lube in bilge

Views: 1,598

Posted By MojoBoss

Thanks Randy - I did put a clean paper towel...

Thanks Randy - I did put a clean paper towel under the lube bottle and no drips after a week - Right now I am disconnecting the quick connect lube line when the boat is in the lift. I was able to see...

Forum: Do It Yourself, Boating on a Budget

09-29-2012, 09:31 AM

Replies: 5

Brovo1 OW220-Water and drive lube in bilge

Views: 1,598

Posted By MojoBoss

Brovo1 OW220-Water and drive lube in bilge

Baja 302 twin 496's 430 hours Drive lube monitor empty - alarm - inspected and found drive lube oil and water in bilge :( . Gear lube quick connects checks ok - clean and dry. I can not physically...

Forum: Do It Yourself, Boating on a Budget

05-19-2012, 12:59 PM

Replies: 6

496 raw water flow exits exhaust are not even

Views: 4,844

Posted By MojoBoss

Using diag computer hooked up to PCM monitoring...

Using diag computer hooked up to PCM monitoring temps underway and at idle a 8 degree split which agree with console gauge temperatures running 159/160 degrees on port and 166/167 starboard engine. ...

Forum: Do It Yourself, Boating on a Budget

05-19-2012, 10:30 AM

Replies: 6

496 raw water flow exits exhaust are not even

Views: 4,844

Posted By MojoBoss

496 raw water flow exits exhaust are not even

a FIY guy with a interesting temp issue. I purchased my boat new 2006 and My 496 starboard engine has always ran about 10+ degrees higher than my port engine - yes, this is not a show stopper by any...

Forum: Do It Yourself, Boating on a Budget

01-14-2012, 01:18 PM

Replies: 4

04/ 496mag-IAC output fault - replaced IAC Fault not cleared

Views: 2,937

Posted By MojoBoss

PCM causing IAC fault

I did Swap the PCM's between engines today and I did not want to believe this problem was a bad PCM but, lo and behold the problem moved with the PCM module. I opened the PCM (yes I wanted to see...

Forum: Do It Yourself, Boating on a Budget

01-11-2012, 03:45 PM

Replies: 4

04/ 496mag-IAC output fault - replaced IAC Fault not cleared

Views: 2,937

Posted By MojoBoss

Thanks for the help - I don't have a wiring...

Thanks for the help - I don't have a wiring schematic so I will try the ohm the wires using color code wire from tip to tip to see if there is a connection problem.
I wont have time till the...

Forum: Do It Yourself, Boating on a Budget

01-09-2012, 07:59 PM

Replies: 4

04/ 496mag-IAC output fault - replaced IAC Fault not cleared

Views: 2,937

Posted By MojoBoss

04/ 496mag-IAC output fault - replaced IAC Fault not cleared

I have an interesting problem beep, beep at console every 2 minutes – 496 mag with 360 hours - an IAC output fault on scanner – nothing new to most but what’s different is that I replaced the IAC and...

Showing results 1 to 9 of 9