Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Fairliner
Showing results 1 to 12 of 12
Search took 0.01 seconds.
Forum: Drives and Lower Units
05-08-2021, 04:51 PM
Replies: 0
Views: 933
Posted By Fairliner

Ssm 3

Looking for advice on what gasket material to use on the plug-in bearing support housing on SSM 3.
Mine is leaking oil, Tried to repair with Permatex RTV form-a-gasket, didn't work. I will check the...
Forum: General Boating Discussion
05-08-2021, 02:08 PM
Replies: 0
Views: 544
Posted By Fairliner

Ssm iii

Hello, looking for advice as to the torque specs for the plug-in bearing support aluminum housing bolts.
Also the gasket material that I should use. Mine is leaking, tried to redo with Permatex RTV...
Forum: Drives and Lower Units
10-09-2016, 03:35 PM
Replies: 0
Views: 1,214
Posted By Fairliner

Speedmaster 3 parts

Looking for driveshaft bearing support for Speedmaster 3 transom plate
Forum: Drives and Lower Units
01-08-2016, 09:28 PM
Replies: 12
Views: 3,966
Posted By Fairliner

I have a R/H drive, and know of a new old stock...

I have a R/H drive, and know of a new old stock one at a Dealer and a used one at another Dealer
Forum: Drives and Lower Units
02-26-2015, 07:36 PM
Replies: 1
Views: 1,250
Posted By Fairliner

Huber 1450

installing a Huber 1450, it has a check valve on the return oil line, is it needed ?
Thanks
Forum: Drives and Lower Units
08-04-2012, 05:01 PM
Replies: 12
Views: 3,966
Posted By Fairliner

Mercruiser III

Thanks all for the replies.Although this is not a go-fast boat,the install that I am doing is not unlike a TR, just bigger. The reason for the conversion is that I cannot match the existing shaft...
Forum: Drives and Lower Units
07-30-2012, 10:42 PM
Replies: 12
Views: 3,966
Posted By Fairliner

Mercruiser III

I am installing a Yanmar 315HP diesel with a Huber1450 Velvet Drive.
The hull is a semi-displacement V. The trany and Merc III will be connected with A jackshaft w/steady bearing (7').
I am looking...
Forum: Drives and Lower Units
07-28-2012, 06:21 PM
Replies: 3
Views: 1,186
Posted By Fairliner

Borg velvet drive mounts

Can you tell me where you D/L that schematic from, I need to reference some of those parts. Thanks,Barry
Forum: Drives and Lower Units
07-27-2012, 04:52 PM
Replies: 12
Views: 3,966
Posted By Fairliner

Mercruiser III

I am ready to cut the transom hole for my Merc III drive.
This is the big older drive with the 1 1/2" shafts. Can anyone advise me if I can use the mercruiser X dimension specs for this drive.
It...
Forum: Drives and Lower Units
05-24-2012, 12:00 AM
Replies: 1
Views: 742
Posted By Fairliner

Borg Warner Question

I have aHuber 1450 plug-in tranny. Is it possible to change output to driveshaft flange? Thanks, Barry
Forum: General Q & A
04-20-2012, 11:51 AM
Replies: 1
Views: 829
Posted By Fairliner

Mercruiser Question

Can anyone tell me the story on a "Mercruiser lll Clubfoot"
Is it a TR version? Why "Clubfoot"?
Forum: General Q & A
03-24-2012, 05:36 PM
Replies: 1
Views: 750
Posted By Fairliner

Mercruiser Question

Can anyone tell me the difference between a Mercruiser lll "Clubfoot"
and a SSM 3 ? Are parts still available for the Merc lll?
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.