Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Gone Fishing
Showing results 1 to 14 of 14
Search took 0.00 seconds.
Forum: General Q & A
03-28-2019, 10:25 AM
Replies: 31
Views: 12,244
Posted By Gone Fishing

Thanks to everyone for their suggestions and...

Thanks to everyone for their suggestions and advice. ! 'm pleased to advise ALL DONE - Unheard of apparently, but the centre part of the impeller was spinning without the rubber blade part...
Forum: General Q & A
03-28-2019, 05:01 AM
Replies: 31
Views: 12,244
Posted By Gone Fishing

That's all ell and good, BUT, like I said "I have...

That's all ell and good, BUT, like I said "I have now narrowed the problem down to being OUTSIDE the boat (leg). No water coming in the boat. I rigged up a hose direct to the thermo housing inlet...
Forum: General Q & A
03-28-2019, 04:44 AM
Replies: 31
Views: 12,244
Posted By Gone Fishing

Please refer to my post, thanks.

Please refer to my post, thanks.
Forum: General Q & A
03-27-2019, 03:22 PM
Replies: 31
Views: 12,244
Posted By Gone Fishing

Hi - I checked the tubes and seals when I changed...

Hi - I checked the tubes and seals when I changed the impeller and all seemed OK. When I put a hose onto the pipe(s) in the lower leg (outdrive), and remove the hose to the thermo housing, water...
Forum: General Q & A
03-27-2019, 03:17 PM
Replies: 31
Views: 12,244
Posted By Gone Fishing

Hi - yeah, did think about doing the. The...

Hi - yeah, did think about doing the. The rotations are opposite, so would have to put them back, but I did consider. Thanks!
#
Forum: General Q & A
03-26-2019, 06:59 PM
Replies: 31
Views: 12,244
Posted By Gone Fishing

Risers and manifolds were ordered with engine...

Risers and manifolds were ordered with engine number and are like for like.
Forum: General Q & A
03-26-2019, 06:57 PM
Replies: 31
Views: 12,244
Posted By Gone Fishing

Thanks - the risers overeat at idle, so the...

Thanks - the risers overeat at idle, so the bulletin isn't relevant. The plastic sleeve i the thermo housing was inserted correctly (I defo wouldn't make a mistake like that). It s design 2 (as...
Forum: General Q & A
03-26-2019, 06:42 PM
Replies: 31
Views: 12,244
Posted By Gone Fishing

JUST TO RECAP GUYS (as a lot of questions and...

JUST TO RECAP GUYS (as a lot of questions and referrals are about things I've already addressed)

"...risers getting very hot, very quickly". "...impeller is good as new". ".. replaced the...
Forum: General Q & A
03-21-2019, 06:34 AM
Replies: 31
Views: 12,244
Posted By Gone Fishing

Like I said in my original post, the risers AND...

Like I said in my original post, the risers AND manifolds are new and replaced like for like! Also, again like I said, the impeller has been checked and is OK.

Engine # OD708642
Forum: General Q & A
03-21-2019, 06:30 AM
Replies: 31
Views: 12,244
Posted By Gone Fishing

All done. Checked hose and flow at that point;...

All done. Checked hose and flow at that point; all seemed OK.
Forum: General Q & A
03-21-2019, 06:29 AM
Replies: 31
Views: 12,244
Posted By Gone Fishing

Yeah, risers get very hot, very quick on just one...

Yeah, risers get very hot, very quick on just one engine. Intake pipe was brand new last year, when bellows etc. and gimble bearing replaced.
I'm using muffs and have checked all flows; all seems...
Forum: General Q & A
03-21-2019, 06:28 AM
Replies: 31
Views: 12,244
Posted By Gone Fishing

All done and checked out OK.

All done and checked out OK.
Forum: General Q & A
03-21-2019, 06:27 AM
Replies: 31
Views: 12,244
Posted By Gone Fishing

Yeah, risers get very hot, very quick on just one...

Yeah, risers get very hot, very quick on just one engine. Intake pipe was brand new last year, when bellows etc. and gimble bearing replaced.
I'm using muffs and have checked all flows; all seems...
Forum: General Q & A
03-19-2019, 06:17 PM
Replies: 31
Views: 12,244
Posted By Gone Fishing

Mercruiser Overheating (so am I)

The boat is out of the water. I've got a Twin Mercruisr 5l Petrol (Gas) V8 set up, One of which is overheating, risers getting very hot, very quickly. I checked the impeller (new last year - less...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.