Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: dlogvine
Showing results 1 to 14 of 14
Search took 0.04 seconds.
Forum: Wanted
01-03-2020, 11:48 AM
Replies: 10
Views: 1,241
Posted By dlogvine

I posted a pic. Do you need a better pic?

I posted a pic. Do you need a better pic?
Forum: General Q & A
12-30-2019, 02:21 AM
Replies: 3
Views: 1,544
Posted By dlogvine

Flywheel for 2000 Mercruiser 4.3 v6 vortec engine

Im looking to buy a Flywheel for the above mentioned engine, but I'm not sure which one should I get. A lot of places post the flywheel for this engine but I hey all have different part numbers even...
Forum: Wanted
12-29-2019, 10:37 PM
Replies: 10
Views: 1,241
Posted By dlogvine

This is the module itself

Connector should fit this plug
https://cimg1.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/720x960/fb_img_1577482056298_22b4af0614b4918c7f57328f65d375b8ead11f1e.jpg...
Forum: Wanted
12-29-2019, 10:36 PM
Replies: 10
Views: 1,241
Posted By dlogvine

Hopefully it will let me post a picture now. Here...

Hopefully it will let me post a picture now. Here is the look of the module on the distributor. I have seen several wiring harnesses for this type of modules on ebay but for some reason every picture...
Forum: Fiberglass and Paint
12-29-2019, 10:33 PM
Replies: 6
Views: 4,960
Posted By dlogvine

man, this is a big project. Good luck!

man, this is a big project. Good luck!
Forum: Fiberglass and Paint
12-29-2019, 10:30 PM
Replies: 9
Views: 6,361
Posted By dlogvine

if you already removed the engine it is a matter...

if you already removed the engine it is a matter of a couple hours to disassemble transom. It is an easy task - V-pipe 4bolts, transom plate 6 or 8 depending on what outdrive you have. If you suspect...
Forum: Fiberglass and Paint
12-29-2019, 10:23 PM
Replies: 6
Views: 2,724
Posted By dlogvine

Depends on how small are the nicks dings and...

Depends on how small are the nicks dings and scratches. If they are small and do not go through the gelcoat, you can just sand it down. If they are deeper and go through the gel coat you might need...
Forum: Fiberglass and Paint
12-29-2019, 10:19 PM
Replies: 9
Views: 2,174
Posted By dlogvine

are you painting it over or gel coating the...

are you painting it over or gel coating the surface? Either way, clean it so there is no dirt or old paint chips (if it was painted over the gelcoat), if it is gel coat surface you can use the high...
Forum: Fiberglass and Paint
12-29-2019, 10:14 PM
Replies: 2
Views: 1,397
Posted By dlogvine

you can try to use Git Rot. Sold in many stores...

you can try to use Git Rot. Sold in many stores including Walmart. You need to drill a couple holes around the rotted place and inject it in. The compound penetrates into the wood and if like you...
Forum: Fiberglass and Paint
12-29-2019, 10:10 PM
Replies: 9
Views: 4,372
Posted By dlogvine

Also before spraying gelcoat, spray a little of...

Also before spraying gelcoat, spray a little of the cleaner as well as immediately after the spraying. I think you can use acetone, but I found a special cleaner in our Space Age Paint store.
Forum: Fiberglass and Paint
12-29-2019, 10:07 PM
Replies: 9
Views: 4,372
Posted By dlogvine

You can use 2.5mm HVLP gun for gelcoat. Just make...

You can use 2.5mm HVLP gun for gelcoat. Just make sure you have a decent compressor that will not run out of air half way through. If you are concerned about the length of the hardening, use about...
Forum: Wanted
12-29-2019, 10:02 PM
Replies: 10
Views: 1,241
Posted By dlogvine

crap, it tells me to wait to post a pic until I...

crap, it tells me to wait to post a pic until I get at least 10 replies.
Forum: Wanted
12-27-2019, 07:48 PM
Replies: 10
Views: 1,241
Posted By dlogvine

Thank you, looks like a great source of...

Thank you, looks like a great source of miscellaneous parts
Forum: Wanted
12-27-2019, 05:43 PM
Replies: 10
Views: 1,241
Posted By dlogvine

Thunderbolt IV 6 pin male connector

Im looking for a Thunderbolt IV ignition module male connector. The module is located on the distributor.
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.